525694
206
Zoom out
Zoom in
Previous page
1/216
Next page
TROUBLESHOOTING
A-16
High-pitched sound
while sewing
Dust or lint is caught in the feed dogs. Remove the dust or lint. A-3
Pieces of thread are caught in the race. Clean the race. A-3
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-42
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized retailer.
A-3
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-39
Character pattern
does not turn out
Wrong presser foot was used. Attach the correct presser foot.
S-68
Pattern adjustment settings were set
incorrectly.
Revise the pattern adjustment settings. S-82
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. S-81
Thread tension is set incorrectly. Adjust the thread tension. S-12
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands
so that the fabric is fed in a straight line.
S-3
Machine does not
operate
There is no pattern selected. Select a pattern. S-21, S-77
“Start/Stop” button was not pushed. Press the “Start/Stop” button. B-13
Main power switch is not turned on. Turn the main power to ON. B-19
Presser foot is not lowered. Lower the presser foot. B-13
“Start/Stop” button was pushed with the foot
controller attached.
Remove the foot controller, or use the foot
controller to operate the machine.
S-4
The “Start/Stop” button was pressed while the
machine is set for the sewing speed controller
to control the zigzag stitch width.
Use the foot controller instead of the
“Start/Stop” button to operate the machine,
or set the “Width Control” to “OFF” in the
settings screen.
B-25, S-4
All keys and buttons have been locked by
.
Press to unlock all keys and
buttons.
B-49, B-51
Nothing happens,
even if the LCD
display is pressed
The screen has been locked. Press either of the following keys to unlock
the screen.
The fabric feeds in the
opposite direction.
The feed mechanism is damaged. Contact your nearest authorized retailer.
The LCD screen is
fogged up.
Condensation has formed on the LCD screen. After a while, the cloudiness will disappear.
Specifying with
sensor pen cannot be
done accurately
The sensor pen has not been calibrated. Before using the sensor pen for the first time,
be sure to calibrate it.
B-64
The pen is being held differently than when it
was calibrated.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned
if the pen is held at a slightly different angle.
In this case, make fine adjustments after
making the selection.
B-64
CAUTION
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,
the machine may feed the fabric even if the needle is raised. This is due to the needle bar release
mechanism. At these times, the machine will make a sound different from what is made during normal
sewing. This is not the sign of a malfunction.
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
Problem Cause Solution Page
206


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Crescendo BLCR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Crescendo BLCR in the language / languages: English as an attachment in your email.

The manual is 12,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Crescendo BLCR

Baby Lock Crescendo BLCR Quick start guide - English, French, Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info