661179
198
Zoom out
Zoom in
Previous page
1/204
Next page
Troubleshooting
A-20
12
OK to recall and resume previous memory? This message appears if the machine is turned off while embroidering, then
turned on again.
Press to return the machine to the condition (pattern position and
number of stitches) when it was turned off. Follow the procedure described
in “If the thread breaks during sewing” on page E-24 to align the needle
position and embroider the remainder of the pattern.
13
Pattern extends to the outside of embroidery frame. This message is displayed when the combined character pattern is too large
for the embroidery frame. You can rotate the pattern 90 degrees and
continue combining characters.
14
Pattern extends to the outside of embroidery frame.
Add no additional characters.
This message is displayed when the character pattern combination is too
large to fit in the embroidery frame. Change the character pattern size or
layout the patterns to fit the embroidery frame. If “Embroidery Frame
Identification View” is set to “ON”, setting to “OFF” or selecting larger frame
may help.
15
Pattern extends to the outside of embroidery frame.
This function cannot be used at this time.
This message appears when the embroidery character pattern is resized or
switched between written vertically/horizontally so that it is too large for the
embroidery frame.
16
Preventive maintenance is recommended. This message is displayed when the machine needs to be maintained. (page
A-3)
17
Raise the buttonhole lever. This message is displayed when the buttonhole lever is down, a stitch other
than a buttonhole is selected, and the “Start/Stop” button, etc. is pressed.
18
Selected pattern field extends to the outside of the
embroidery frame.
This message appears when the selected embroidery pattern is larger than
the large embroidery frame. Reduce the pattern size, or select a different
pattern.
This message appears when the selected embroidery pattern is larger than
the embroidery frame selected when “Embroidery Frame Identification View”
is set to “ON”.
19
The bobbin thread is almost empty. This message is displayed when the bobbin thread is running out. Follow the
procedure described in “If the bobbin runs out of thread” on page E-23.
20
The bobbin winder safety device has activated. Is
the thread tangled?
This message is displayed when the bobbin is being wound, and the motor
locks because the thread is tangled, etc.
21
The carriage of the embroidery unit will
move. Keep your hands etc. away from the
carriage.
This message appears before embroidery unit moves.
22
The pockets are full. Delete a pattern. This message is displayed when the memory is full and a pattern must be
deleted.
23
The safety device has been activated. Is the
thread tangled? Is the needle bent?
This message is displayed when the motor locks due to tangled thread or for
other reasons related to thread delivery.
24
The "Start/Stop" button does not operate with the
foot controller attached. Remove the foot controller.
This message is displayed when the “Start/Stop” button is pressed to sew
Utility stitches or Character/Decorative stitches while the foot controller is
connected.
25
There is a pattern included that cannot be saved to
USB media. Save the pattern in the machine's
memory.
Depending on the pattern, it may not be possible to save it to a USB flash
drive.
26
This pattern cannot be used. This message appears when you try to retrieve a pattern that cannot be used
with this machine.
27 This USB media cannot be used. This message is displayed when you try to use incompatible media.
28
Turn off the power and replace the needle
plate.
This message is displayed when you try to sew with a stitch other than a
straight stitch (middle needle position) while the straight stitch needle plate is
installed.
This message is also displayed when the needle plate is removed while the
machine is still turned on.
29 USB media error This message is displayed when an error occurs with the USB flash drive.
Error messages Cause/solution
198


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Accord BLMCC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Accord BLMCC in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Accord BLMCC

Baby Lock Accord BLMCC Additional guide - English - 44 pages

Baby Lock Accord BLMCC Quick start guide - English - 24 pages

Baby Lock Accord BLMCC Additional guide - French - 44 pages

Baby Lock Accord BLMCC Quick start guide - French - 24 pages

Baby Lock Accord BLMCC Additional guide - Spanish - 44 pages

Baby Lock Accord BLMCC Quick start guide - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info