661179
196
Zoom out
Zoom in
Previous page
1/204
Next page
Troubleshooting
A-18
After sewing
Symptom Probable Cause Remedy Reference
Thread tension is
incorrect.
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine.
B-23
Bobbin is set incorrectly. Reset the bobbin. (If needle plate was removed,
reinstall needle plate and tighten screws prior to
installing bobbin case. Check to make sure
needle enter through the center of needle plate
opening.)
B-20, A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-30
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. B-33
Thread tension is set incorrectly. Adjust the thread tension. B-42
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-20
Needle is turned, bent or the point is dull. Replace the needle. B-31
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-17
Character or
decorative patterns
are misaligned.
Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. D-5
Pattern does not
turn out.
Wrong presser foot was used. Attach the correct presser foot. B-34
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. D-4
Thread tension is set incorrectly. Adjust the thread tension. B-42
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands so
that the fabric is fed in a straight line.
B-36
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
A-2
Embroidery pattern
does not sew out
correctly.
Thread is twisted. Use scissors, etc., to cut the twisted thread and
remove it from the bobbin case, etc.
A-8
Thread tension is set incorrectly. Adjust the thread tension. B-42
Fabric was not inserted into the frame correctly
(fabric was loose, etc.).
If the fabric is not taut in the frame, the pattern
may turn out poorly or there may be shrinkage
of the pattern. Set the fabric into the frame
correctly.
B-58
Stabilizing material was not attached. Always use stabilizing material, especially with
stretch fabrics, lightweight fabrics, fabrics with
a coarse weave, or fabrics that often cause
pattern shrinkage. See your authorized Baby
Lock retailer for the proper stabilizer.
B-58
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing.
If the frame bumps something during sewing,
the pattern will turn out poorly. Do not place
anything in the area where the frame may bump
it during sewing.
B-57
Fabric outside the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move.
Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the sewing
arm, and rotate the pattern 180 degrees.
B-58
Fabric is too heavy, so the embroidery unit
cannot move freely.
Place a large thick book or similar object under
the arm head to lightly lift the heavy side and
keep it level.
196


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Accord BLMCC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Accord BLMCC in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Accord BLMCC

Baby Lock Accord BLMCC Additional guide - English - 44 pages

Baby Lock Accord BLMCC Quick start guide - English - 24 pages

Baby Lock Accord BLMCC Additional guide - French - 44 pages

Baby Lock Accord BLMCC Quick start guide - French - 24 pages

Baby Lock Accord BLMCC Additional guide - Spanish - 44 pages

Baby Lock Accord BLMCC Quick start guide - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info