496152
11
Zoom out
Zoom in
Previous page
1/24
Next page
7a: Setting Up the 8000AP - 1
Getting Started
Configuring the 8000AP
Read this manual thoroughly so you get to understand the
main controls of the 8000AP and how they work.
Switch on all source units (and the TV monitor if used).
Connect the 8000AP to the mains power and switch on.
Switch the unit on via tye mains switch on the rear panel.
Press the key on
the handset or the front panel.
Now switch on the power amplifier/s.
When setting up your unit for the first time the process will be
simplified if you run the as this will ensure
you enter all the essential parameters required.
Once the required settings are input and saved, you may alter
them at any time. Changes will be retained when the unit is
switched off or even if the mains power is removed, provided
they have been saved.
You must connect your television to the output in order
for the on-screen information to be displayed.
The QSet menu enables you to set basic parameters of the
8000AP from the front panel without using a TV connection.
The QSet menu is intended for use when the 8000AP is
operational. The OSD set-up menus contain items absent in
the QSet menu and vice versa, so both menus should be
enabled if you wish to take advantage of the full range of set
up possibilities featured in the 8000AP.
Make sure your power amplifier/s are switched off.
NOTES:
The power LED will illuminate, the front panel display window
will show the Model No and the software version.
The 8000AP will then go into Standby.
To bring the unit out of standby: Standby
On Screen Display Menu
On-screen Set-up
OSD
QSet (Quick set)
Press the keys to select
Press
Press the keys to select
Press the keys to toggle or
If you select No further action is needed.
If you select You will be
asked to set the bass cut
frequency:
Press to select 50Hz,
80Hz, 100Hz, 120Hz.
Now press to select
.
įĬ
įĬ
ǡǠ
įĬ
“Speaker Sizes”
ENTER
“Speaker Sizes”
Large Small
Large:
Small:
Centre
Do you have a centre
speaker?
After setting up the size and bass parameters of the
centre speaker:
Entering and Navigating the Set Up Menu
Loudspeaker set-up
The on-screen set-up menus are operated by the handset.
To enter set-up mode, press the key.
You may need to set
the TV system in the QSet menu. Refer to Page 19
Press the keys to navigate
the cursor to the desired option.
Press ENTER to access the sub-
menu
Press BACK to jump back up to
the front page
Press the MENU key to exit the
OSD menu and save the setting.
If you have not made any changes to your settings you will
simply exit the on-screen menu system.
The 8000AP factory settings allow you to operate
your system “straight out of the box” but the unit will not
perform at its best until you fully set it up. Also the pre-set
configurations may not correspond to your system.
You will be asked to enter which speakers are present in your
system, whether they are “Large” or “Small”. If you select
“Large” the full bass range will be delivered to the speakers. If
you select “Small” you will be asked to enter the frequency at
you wish to cross them over to the sub-woofer. (refer to your
loudspeaker manuals for details)
MENU
NAVIGATING THE MENUS
NOTE:
If the Menu screen does not appear:
įĬ
Page 9
Audiolab 8000AP
V 3.20 HD0.35
ENTER
BACK
If you select for the front
speakers you may only select
Small
Small Noneor
If you select for the
front speakers you may select
Large
orLarge, Small, None
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiolab 8000AP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiolab 8000AP in the language / languages: English as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info