496152

Audiolab 8000AP Manual

12
Zoom out
Zoom in
Previous page
1/24
Next page
7b: Setting Up the 8000AP - 2
• Press to
jump up to the
front page
• Press the
keys to select
• Press
Press the
keys to select
You will hear a burst of white noise from the Left Front speaker.
The volume at the Left Front speaker sets the reference level
for the calibration. All levels must be set to this reference.
Individual levels can be varied by up to +/- 10dB.
When the noise generator Is turned on, the volume
automatically goes to -30dB. This master level may be
adjusted to suit your system with the volume control on the
front panel or via the handset.
Set the meter to ‘C’ weighting
with ‘slow’ response and to read 75dB SPL at centre scale.
Place the meter at ear level at your listening position.
Point the microphone at the ceiling.
Adjust the Volume level so the sound level meter reads75dB.
Select each speaker in turn. Adjust the relative channel levels
on-screen using the keys on the handset until the sound
level meter reads 75dB on all channels.
Sit in your normal listening
position. With the Volume keys, set the Left Front speaker
to the equivalent to normal conversation. Now select each
speaker in turn and adjust the on-screen level using the
keys on the handset to sound the same as the Left Front
speaker. During this process you may have to re-visit some
loudspeakers to reset the level.
Leave the subwoofer level on the screen at 0dB. Adjust the
subwoofer’s volume control to sound as close to the reference
Left Front speaker as you can. Now trim the on-screen
subwoofer level with the keys on the handset. The object
is to get the subwoofer level as close to 0dB as possible.
BACK
Speaker Levels.
ENTER
•
Noise On
Setting up the Subwoofer input level:
įĬ
ǡǠ
ǡǠ
įĬ
ǡǠ
ǡǠ
Do not adjust the volume
during calibration after the level is established.
Using a Sound Level Meter:
seated
Set Up By Listening- seated
Do not adjust the volume control during the calibration.
Loudspeaker Distances
Speaker Calibration
• Press to jump back up to the front page
• Press the keys to select
• Press
These measurements are used by the 8000AP in surround
modes to correct for delays in sound reaching your ears due
to differences in the distance between each speaker and the
listening position.
Use the keys to select the loudspeaker and the keys
to vary the distance. The distance can be set from 0 to 10
metres in units of 25cm. A speaker entered as will have
no distance shown on the screen.
Speaker calibration is essential to achieve a correctly centred
soundimage;followitcarefully.Wesuggestyouuseasound
level (SPL) meter; otherwise you can set up the levels by ear- you
will have to be careful to match the output levels for each
speaker to sound equally loud.
BACK
“Speaker Distance”.
ENTER
none
įĬ
įĬ ǡ Ǡ
Page 10
• Press the
keys to select
• Press
: you will be
able to select or for the surrounds.
: you will be
able to select or for the surrounds.
• Press the
keys to select
• Press
By default the Back speakers are fixed at with
predetermined bass cut-off at 100 Hz. You can select
(for 6.1) or (for 7.1).
• Press the
keys to select
• Press
• Select
įĬ
įĬ
įĬ
“Surround”.
ENTER
If you have set the front speakers to Large
Large, Small None
If you have set the front speakers to Small
Small None
After setting up the size and bass parameters of the
surround speakers:
“Back”
ENTER
Small
None,
One , Two
After setting up the size and bass parameters of the
back speakers:
“Subwoofer”
ENTER
Yes/ No
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiolab 8000AP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiolab 8000AP in the language / languages: English as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info