810507
43
Zoom out
Zoom in
Previous page
1/60
Next page
41
Degree of protection IP
The cover of the operating module of the controller ensures different degrees of IP
protection, depending on the method of installation. After installation performed
according to this figure on the front of the operating module cover, the device has a
degree of protection IP20 (indicated on the rating plate). On the side of the terminals, the
cover has an IP00 degree of protection, therefore the terminals of the operating module
must be installed in such a way that access to this part of the housing is prevented. If it is
necessary to gain access to the parts with terminals, it is necessary to disconnect the power
supply, make sure that the terminals and cables are not energized, and only then remove
the cover of the operating module.
Wiring connection
The controller is designed for power supply with voltage 230V ~, 50Hz.
Properties of electrical installation:
three - core cable (with protective conductor),
carried out in accordance with valid regulations,,
Equipped with a residual current device with an operating current of IΔn≤30mA, which
protects against the possibility of electric shock and limits damage to the device,
including fire protection.
ATTENTION: Dangerous voltages can be present at the controller terminals
when the controller is switched off using the keys. Before starting installation
work, it is essential to disconnect the mains voltage and make sure that the
terminals and cables are not under dangerous voltage. Equipped with a residual
current device with an operating current of IΔn≤30mA, which protects against
the possibility of electric shock and limits damage to the equipment, including
fire protection.
The connecting cables must not touch surfaces with a temperature exceeding their
nominal operating temperature.
The terminals of each module, numbered 1-21, are intended for the connection of devices
with a mains voltage of 230V ~. Terminals 22-49 are designed for cooperation with low
voltage devices (below 12VDC).
Connecting the 230V ~ mains voltage to terminals 22-49 and the RS485
transmission connector will damage the controller and cause a risk of electric
shock!
The ends of the connecting cables, especially the power cables, must be protected by
insulated crimp terminals, as shown in the following figure:
3URWHFWLRQRIFDEOHV¶HQGVDFRUUHFWELQFRUUHFW
Feed cable must be connected to the terminals marked with an arrow .
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK Pellet 30 Automatic Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK Pellet 30 Automatic Plus in the language / languages: English as an attachment in your email.

The manual is 0.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATTACK Pellet 30 Automatic Plus

ATTACK Pellet 30 Automatic Plus User Manual - German - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info