810499
28
Zoom out
Zoom in
Previous page
1/92
Next page
28
[A 99] Temperature of boiler overheating – defines the value of boiler temperature to activate
the alarm of the boiler overheating.
[Fd60]Duration of boiler stop by ignition and fuel shortage – this parameter defines the
maximum time between starting the controller by the START button and achieving the
controller´s operating mode (reaching the flue gas temperature of [
c
90]). If the temperature of
[
c
90] is not reached during the heating up, the fan is stopped and the alarm FUEL (fuel shortage)
is displayed.
[Fb30]Duration of boiler stop by flue shortage and burn-down– the fuel amount test is
activated in the operating mode, when the flue gas temperature decreases under the parameter
[
c
90] or (if the flue gas sensor is not connected) when the boiler temperature decreases under
the adjusted parameter [L 45]. If the temperature does not exceed the necessary limit during this
period, the controller displays FUEL alarm.
[Ar 0] The control of the additional output-regulator is equipped with an additional
multifunctional output compatible with the options listed below (it is necessary to use the
additional UM-1 module for this purpose):
[Ar 0] parameter – indicates start of the automatic boiler (e.g. gas or pellet boiler). When
the controller is started and the boiler generates heat, the automatic boiler is stopped.
Operation of the automatic boiler is blocked by the controller in the operating mode. The
automatic boiler is started by controller, when the fuel is burned down in the boiler and
the FUEL alarm is displayed.
[Ar 1] parameter – indicates that the additional multifunctional output will be used for
error messages like boiler sensor failure, overheating or fuel shortage.
[
c
240]Adjusted flue gas temperature – the controller will struggle to reach and to keep this
value. The flue gas temperature sensor is turned off, if this parameter is set to „- -“.
[
c
h5]Hysteresis of flue gas temperature – defines the difference for which must the flue gas
temperature decrease to increase the fan rotations.
[
c
t 5]Time constant of stabilization the flue gas temperature – defines the period of
adjusting the fan rotations during stabilization of the flue gas temperature. If the flue gas
temperature exceeds the value given by the parameter [
c
240], the controller starts to decrease
the fan rotations gradually, until the flue gas temperature decreases to the adjusted value. If the
flue gas temperature decreases to the value of flue gas temperature hysteresis, the controller
starts to increase the fan rotations gradually.
[
c
F10]Blower speed jump while stabilizing exhaust gas temperature – defines the change of
rotations to achieve the adjusted flue gas temperature.
[
c
90]Flue gas temperature by fuel shortage – the message „FUEL“ for fuel shortage is
displayed after the flue gas temperature decreases under this value.
3.8 TESTING THE REGULATOR OUTPUTS
It is possible to make a check to test the correct functionality of the regulator and devices
connected. The correct function of fan is tested by selecting the [outΠ] on display and holding
the „OK“ button. Test of the circuit pump is done by selecting the [outP]. Select the [outu] to
start the additional output and [outr] for multifunctional additional output.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK DPX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK DPX in the language / languages: English as an attachment in your email.

The manual is 11.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATTACK DPX

ATTACK DPX Additional guide - English - 21 pages

ATTACK DPX Additional guide - German - 21 pages

ATTACK DPX User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info