519929

Atika ST 300 Manual

20
Zoom out
Zoom in
Previous page
1/114
Next page
19
Adjusting from 0° – 90 °
1.
Loosen the star handled nut (12) and turn the angle
stopper (11) until the desired angle is indicated on the
scale (0°- 90°).
2.
Refasten the star handled nut in order to fix the
adjusted angle.
3.
, Put the tile on the stop rail (10) and the angle
stopper (11).
4. Start the machine and wait until the cooling water is
flushed to the cutting-off wheel.
5.
, Pull the cutting unit (14) by moving the handhold
(16) slowly and constantly through the tile.
6. Switch off the machine after finishing the cut.
Setting of mitre cut
1.
Loosen the locking screws (6) on both sides of the
machine and swivel the guide bar (13) to the desired
angle position.
2.
Refasten the set screws (6).
3. Carry out the cut as described in point „Adjusting from 0°-
90°“.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work
− switch off device
− wait for standstill of the stone cutter
− pull out main plug
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance
Replacing cutting-off wheel
Before replacing the cutting-off wheel
pull out the power plug.
Vor dem Wechseln der Trennscheibe den
Netzstecker ziehen.
Do not use any damaged cutting-off wheels or such which
have changed their shape.
Only use sharp cutting-off wheels.
Replacing cutting off wheel
1. Loosen the screws (30) and swivel the cover hood (19)
to the side.
2.
Position the ring wrench (22) on the forward hexagon
nut (33) and the installation wrench (21) on the motor shaft
end and loosen the first hexagon nut (33).
L Left-handed thread!
Loosen the 2
nd
hexagon nut (33) in the same way.
3. Remove the flange (31) toward the front.
4. Now you can remove the cutting-off wheel (20).
5. Check the spindle, hexagon nuts and flanges (31, 32) for
damages, wear or loose fit before mounting the cutting-off
wheel. Immediately replace damaged or worn parts.
6. The installation of the cutting-off wheel is carried out in
reverse order.
L Observe the rotational direction! The rotational
direction arrow printed on the cutting-off wheel must agree
with the rotational direction arrow on the cover hood.
6. Firmly tighten the hexagon nuts (31).
L Left-handed thread!
7. Screw on the covering cap (19).
Cleaning
L
Observe the following in order to keep the operability of
the stone cutter :
Clean all moving parts regularly.
Remove dust and dirt with a cloth or a brush.
Do not clean the machine with running water or high-
pressure cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol,
etc.) as these can damage the synthetic parts.
Clean the collecting trough and the cooling water pump after
each application in order to guarantee the cooling of the
cutting-off wheel. To empty the trough (8), remove the
closing plug (34) and allow the water to drain into a suitable
vessel.
Clean the inside of the cover hood regularly.
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
Remove the mains plug before each
transport.
L
Transport the stone cutter only when the cutting unit is
fixed:
For this purpose screw the safety pin (27) into
the motor cover
Then screw the machine knob nut (26) open.
Fasten the cutting unit to the motor housing
using the transport screw (28).
That's how you avoid injuries on the hands.
L
Drain the cooling solution completely before any
transport.
A second person is required to assist with the transport.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 300 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info