519929

Atika ST 300 Manual

19
Zoom out
Zoom in
Previous page
1/114
Next page
18
P
P
r
r
e
e
p
p
a
a
r
r
i
i
n
n
g
g
f
f
o
o
r
r
c
c
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
L
To achieve perfect function of the machine, follow the
notes given in these instructions
Setting up the device
Unfold the frame.
A second person is required.
Remove the transport screw for the cutting unit (28).
Unscrew the machine knob nut (26) and the motor safety
pin (27).
Put the cooling water pump (24) into the intended gap of
the trough. Guide the hose and the cable through the
bracket (29). Fill water into the trough until the cooling
water pump is covered with water.
Mount the angle stop (11).
C
C
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug
L
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
Use connection cable or extension cable respectively with a
cross section of at least 1,5 mm².
Daily checks of the PRCD (residual-current-operated
circuit breaker)
The device must be connected via the residual-current-
operated circuit breaker (PRCD).
„Reset“
„Test“
Perform this check once in a
day.
When changing the location
no further test is required.
1. Directly plug the PRCD into the outlet (vertical).
2. Press the “Reset” key – you will hear a click and the
indicator panel will light up red.
3. To check the PRCD press the “Test” key. The inspection
panel no longer shows any colour.
4. Press the “Reset key” again – the indicator panel will light
up red again.
5. The machine can be started.
Switch on
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the PRCD is operative: indicator panel red.
Press the green button ( I ) on the
switch. At the same time, check
whether the rotating direction of the
cutting-off wheel corresponds to
the indicated rotational direction on
the protection cover (arrow).
L
If there is a power cut, the machine switches off automati-
cally. To restart, press the green button again.
Switching off
Press the red button ( 0 ) on the switch.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
Before commencing work, ensure the
following:
Workplace tidied?
Is the stone cutter stably mounted?
Check before starting to work whether the rotational
direction of the cutting-off wheel agrees with the rotational
direction indicated by the arrow on the cover hood.
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Working with the stone cutter
Keep your hands always in a safe distance to the
rotating cutting-off wheel.
Do not start working before the cutting-off wheel has
reached its maximum rotational frequency.
Pay attention to that the cooling water pump washes water
to the cutting-off wheel.
Only workpieces which have been securely mounted and
aligned can be processed.
In any case, adhere to all safety notes (see "Safe
working").
A
A
d
d
j
j
u
u
s
s
t
t
m
m
e
e
n
n
t
t
s
s
o
o
n
n
t
t
h
h
e
e
s
s
t
t
o
o
n
n
e
e
c
c
u
u
t
t
t
t
e
e
r
r
Carrying out angle cuts
Make sure the machine is switched off when performing
adjustment tasks and push the saw head toward the
rear.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 300 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info