519929

Atika ST 300 Manual

18
Zoom out
Zoom in
Previous page
1/114
Next page
17
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away from
the reach of children.
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths up to 25 m
2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
/
/
s
s
p
p
a
a
r
r
e
e
p
p
a
a
r
r
t
t
s
s
Pos. Denomination Order-No.
1. Rear frame section 364042
2. Front frame section 364043
3.
Frame 364044
4. Support brace
364045
5. Lateral support
364046
6. Locking nut for mitre cut
364047
7. Scale for mitre cut
364048
8. Trough
364049
9. Table plate (3 pieces)
364050
10. Stopper bar (2 pieces) with scale
364051
11.
Angle fence 364052
12.
Star handled nut M6 for angle
adjustment
364053
13. Guide bar
364054
14. Cutting unit
364055
15.
On-off switch 364056
16. Handhold
364057
17 Splash guard 364058
18. Hose 364059
19.
Covering cap 364060
20.
Cutting-off wheel Ø 200 x Ø 25,4 x 2,2
mm
364067
21.
Installation wrench 364040
22.
Socket wrench SW 30 364039
23.
PRCD (residual-current-operated circuit
breaker)
364041
24. Cooling water pump 364061
25. Safety label 364010
26. Machine knob nut M6 364053
27. Motor safety pin 364063
28. Transport screw for cutting unit 364064
29.
Holding eyelet for cooling water hose
364065
30. Hexagon screw M6 x 18 364066
31. Front flange 364038
32. Rear flange 364070
33. Hexagon nut M 16 LH 364071
34. Closing plug 364072
35. Fan (not illustrated) 364074
36. Fan cooling (not illustrated) 364075
37. Capacitor (not illustrated) 364073
38. Hose clamp (not illustrated) 364062
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 300 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info