519275

Atika ST 250 Manual

16
Zoom out
Zoom in
Previous page
1/96
Next page
15
Preparing for commissioning
L
To achieve perfect function of the machine, follow the
notes given in these instructions
You have to attach the following parts:
Base frame
Cooling water pump
Assembly of the base frame and the cooling water
pump -
1. Assemble the main pillars (1) with the screws (4) and the
spring washers (5) on the frame.
2. Screw the clamp holders (6) with the star handle nuts (7)
and the coach bolts (8) on the frame (3).
3. Put the trough (9) into the frame (3).
4. Put the cooling water pump (26) into the intended gap of the
trough.
5. Fill water into the trough until the cooling water pump is
covered with water.
6. Put the radial tile cutter into the trough.
Commissioning
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug
L
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
Use connection cable or extension cable respectively with
a cross section of at least 1,5 mm².
Daily checks of the PRCD (residual-current-operated
circuit breaker)
The device must be connected via the residual-current-
operated circuit breaker (PRCD).
„Reset“
„Test“
Perform this check once in a
day.
When changing the location
no further test is required.
1. Directly plug the PRCD into the outlet (vertical).
2. Press the green Reset key – you will hear a click and the
indicator will light up orange.
3. To check the PRCD press the blue test key. The indicator
panel should no longer light.
4. Press the Reset key again – the indicator panel will
light up orange.
5. The machine can be startet.
Switch on
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the PRCD is operative: indicator panel orange.
Press the green button ( I ) on the
switch. At the same time, check
whether the rotating direction of the
cutting-off wheel corresponds to
the indicated rotational direction on
the protection cover (arrow).
L
If there is a power cut, the machine switches off automati-
cally. To switch on again, first press the red and then the
green button.
Switching off
Press the red button ( 0 ) on the switch.
Working instructions
Before commencing work, ensure the
following:
Workplace tidied?
Is the radial tile cutter stably mounted?
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Working with the radial tile cutter
Keep your hands always in a safe distance to the
rotating cutting-off wheel.
Do not start working before the cutting-off wheel has
reached its maximum rotational frequency.
Pay attention to that the cooling water pump (26) washes
water to the cutting-off wheel.
Only workpieces which have been securely mounted and
aligned can be processed.
Ensure that you always comply with the safety
instructions given on p. 13 ff.
Adjustments on the radial tile cutter
Replacing cutting-off wheel
Before replacing the cutting-off wheel pull
out the power plug.
Do not use any damaged cutting-off wheels or such which
have changed their shape.
Only use sharp cutting-off wheels.
B
D
C
B
D
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info