519275

Atika ST 250 Manual

15
Zoom out
Zoom in
Previous page
1/96
Next page
14
Wear protective clothing:
− ear protection (Sound intensity level at workplace can
exceed 85 dB (A))
− safety goggles
− gloves
− Dust protection mask when carrying out works that
produce a lot of dust
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Take into consideration environmental influences:
− Do not use the device in moist or wet ambience.
− Do not expose the radial tile cutter to rain.
− Provide for good illumination.
Never leave the machine unattended.
Children and youngsters less than 18 years of age and
people who have not read the operating manual must not
operate the machine.
Keep other persons away.
Do not allow other persons, especially children, to touch
the tool or cable.
Keep them away from your working area.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
Do not use any cutting-off wheels which do not correspond
to the indicated characteristics of this instruction manual.
Do not use any cutting-off wheels which have a maximum
rotational frequency of less than 3000 revolutions per
minute.
Pay attention to that the water pump is covered with water.
The use of other tools and other accessories can
signify a risk of injury for you.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− maintenance and cleaning
− Elimination of failures (that includes also freeing a
blocked cutting-off wheel)
− transport and storage
− Leaving the radial tile cutter (also for short-term
interruptions)
Attention! Cutting-off wheel keeps running for a
moment after switching off! Do not brake the cutting-off
wheel with the hand or lateral pressure.
Maintain your radial tile cutter with care:
− Keep the tools sharp and clean to be able to work
better and more safely.
− Follow the servicing instructions and the information
about changing tools.
− Keep handles dry and free of oils and grease.
Check the machine for possible damage:
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
− Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged, All
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away
from the reach of children.
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
− 1.5 mm
2
for cable lengths up to 25 m
− 2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power;
the function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with
this material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures –
must be observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ST 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ST 250 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info