520784
19
Zoom out
Zoom in
Previous page
1/141
Next page
18
2. Incline the saw head to the left to the desired angle.
3. Firmly tighten the incline fixing know again.
4. Cut the work piece as described under "Straight cuts".
Double mitre cuts -
Increased danger of injury exists with the double mitre cut
because of the saw blade being more accessible due to its
heavy incline. Keep your hands far enough away.
1. Loosen the fixing screw for the rotary table (6) and turn the
saw head to the right or left to the desired angle.
2. Firmly tighten the fixing screw again.
3. Loosen the incline fixing screw (20).
4. Incline the saw head to the left to the desired angle.
5. Firmly tighten the incline fixing know again.
6. Cut the work piece as described under "Straight cuts".
Maintenance and cleaning
Before each maintenance and cleaning work
switch off device
wait for standstill of the saw blade
pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or compa-
nies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
L Observe the following to maintain the functionality of the
saw.
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
L Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Take care that the saw blade remains free of rust and resin.
Remove resin residues from the surface of the rotary table.
L Resin residues can be removed with a commercial
maintenance and care spray.
The saw blade is a wearing part and will become dull after
prolonged or frequent use.
Replace the saw blade in that case.
Thoroughly shake out the dust bag. Wash the dust bag in
case of heavy soiling but at least once a year with a mild
soap solution.
Maintenance
Changing the saw blade -
Danger of cutting! Wear gloves when replacing the saw
blade.
Use only suitable saw blades.
Danger of burning! The saw blade is still hot shortly after
cutting.
1. Position the saw head in transport position.
2. Push the saw blade locking device (25).
3. Slowly turn the saw blade by hand until the saw blade lock-
ing device catches.
4. Unscrew the hexagonal screw (26) for the saw blade (left-
handed thread!)
5. Loosen the transport locking pin (5) and turn the saw head
up again.
6. You can now remove the front saw blade flange (27), the
saw blade (16) and the rear saw blade flange (28).
7.
L Clean the saw blade flanges (27, 28).
8. Position the rear saw blade flange again.
9. Insert a new saw blade.
L Pay attention to the correct running direction of the saw
blade: The arrow on the saw blade and the arrow on the pro-
tective cover must point in the same direction!
10. Position the front saw blade flange again.
11. The further assembly is now done in reverse sequence.
Replacing the carbon brushes
Replace the carbon brushes once they have been worn down to
approx. 4 mm.
1. Remove the carbon brush cover on the side of the motor
cover by turning it counterclockwise using a suitable screw
driver.
2. Remove the carbon brushes; note the position of the spring
retention.
3. Insert the new carbon brushes (33) observing the correct
position of the spring retention.
4. Replace the carbon brushes only in pairs.
5. Screw in the carbon brush cover again.
Transport
Remove mains plug before each transport.
L
Before each transport:
Position saw head vertically
Turn rotary table to 0°
Push handle (3) down and engage the transport locking
pin (5)
F
G
J H
H
I
J
K
A
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika KGS210N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika KGS210N in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info