520784

Atika KGS210N Manual

17
Zoom out
Zoom in
Previous page
1/141
Next page
16
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and adjust-
ing tools are removed.
Store the unused machine in a dry locked place away from
the reach of children.
Make sure that only spacer disks and spindle rings are used
which are suited for the purpose indicated by the manufac-
turer.
Electrical safety
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-profile section of at least
− 1.5 mm
2
for cable lengths up to 25 m
− 2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic mate-
rial of same mechanical stability or be covered with this ma-
terial.
The connector of the connection cable must be splash-proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especial-
ly approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or
one of our customer service points. Local regulations – es-
pecially regarding protective measures – must be ob-
served.
Repairs to other parts of the machine must be carried out by
the manufacturer or one of his customer service points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such ac-
tion.
Preparing for commissioning
Loosen the transport locking pin before first use and after each
transport:
Slightly push the handle (3) down
Pull out the transport locking pin (5)
L
To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the machine at a location that meets the following
conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
To ensure a safe position of the saw it must be bolted down
on a solid surface (e.g. workbench or support frame) at opti-
mal working height:
− Disengage the transport locking pin
− Make 4 holes in the support matching the holes in the
base plate.
− Bolt the device down.
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− the saw blade for flawless condition
Do not use deformed or damaged saw blades.
Connect the mitre crosscut saw to a dust collection device
when cutting wood.
Commissioning
L Mains connection
Compare the voltage listed on the device type plate, e.g. 230 V,
with the mains voltage and connect the device to the corre-
sponding and proper socket.
Connect the machine via a 30 mA fault-current circuit breaker.
Use the connection or extension cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths up to 25 m
2.5 mm
2
for cable lengths over 25 m
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switch on
Activate the On/Off switch (2).
Switching off
Release the On/Off switch again.
Dust/chip exhaustion
The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
Unless the machine is used outdoors, the dust bag (21) or a
chip exhaust system must be connected.
A
A
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika KGS210N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika KGS210N in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info