701023
21
Zoom out
Zoom in
Previous page
1/146
Next page
21
Cutting long workpieces
Secure long workpieces against dropping down when
finishing the cutting process. Use roller supports or similar
devices for this purpose.
The sawing process
1. Select and adjust parallel stopper (8) and saw table incline
corresponding to the cutting type.
When sawing with parallel stopper and inclined
saw table the work piece can cant. The parallel stopper
must therefore be fixed on the downwards inclined side of
the saw table.
2. Adjust distance between saw band coping and work piece
to 3 mm.
3. Put work piece on the saw table.
4. Put in power plug.
5. Switch on saw.
6. Saw through work piece in one work step.
Hint:
Make always a test cut to be able to correct the
adjustment.
7. Switch off saw when it is not intended to go on sawing.
Maintenance and cleaning
Before each maintenance and cleaning work
switch off device
wait for stop of saw
pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
Observe the following to maintain the functionality of
the saw.
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Provide that the saw band stays rust-free and resin-free.
Remove all resin residues from the saw bench top.
Resin residues can be removed with a commercial
maintenance and care spray.
Treat the surface of the saw table after cleaning with an
anti-blocking agent.
The saw band is a wearing part and becomes edgeless
after longer or more frequent use respectively.
Renew then the saw band.
Maintenance
Saw band exchange
Danger of cutting! Wear gloves when replacing the
saw band.
Only use suitable saw bands.
1.
Unscrew the two star knob nuts (A) and the nut (B) on
the underside of the saw table (6).
7. Pull off the stopper guidance profile (7).
2.
Open both case doors (2 / 4).
3. Put the saw band coping (11) completely down.
4. Put upper band roll (13) down.
turn the adjusting wheel (1) anti-clockwise, the saw band
is relaxed
5. Take out saw band.
6. Put in new saw band.
Pay attention to a correct position: the teeth must
show forward (direction door).
7. Put saw band centrally on the band rolls (13) / (5).
8. Turn adjusting wheel (1) clockwise until the saw band does
not glide off any longer.
9. Fasten guidance gib (7) and close lower case door.
10. Subsequently:
Clamp saw band („Saw band tension“ p. 19)
Adjust saw band („Incline of the upper band saw roll“ p.
19)
Adjust band guidances („upper band guidance“ and
„lower band guidance“ p. 21)
Keep saw running at least one minute for testing
Switch off saw, pull out power plug and recheck
adjustments
Adjusting upper band guidance
The upper band guidance consists of:
two guide pins (these guide the saw band laterally)
a support roller (this supports the saw band from behind)
Check the two guide pins and the support roller after
each saw band exchange and each saw band
adjustment and readjust it if necessary.
Guide pins and support roller are wear parts. Check
these regularly and replace the rolls in case of wear at
the same time.
To adjust the guide pins:
1. Release screws (J / K).
2. Push the guide pins (L/ M) against the saw band.
3. Open upper door and turn band saw roll several times
manually clockwise.
Both guide rollers must abut slightly on the saw band.
4. Fasten screws (J / K).
5.
Close upper case door.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BS 205-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BS 205-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atika BS 205-2

Atika BS 205-2 Installation Guide - English, German, Dutch, Danish, French, Italian, Polish, Swedish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info