701023
19
Zoom out
Zoom in
Previous page
1/146
Next page
19
Start-up
Mains connection
Compare the voltage listed on the machine’s type plate, e.g.
230 V, with the mains voltage and connect the machine to a
suited and and properly earthed electrical socket.
AC-motor
Use an electrical socket with a rated voltage of 230 V with a
fault-current circuit breaker (30 mA).
Main fuse: 10 A slow
Use an connecting or extension cable in compliance with IEC
60245 (H 07 RN-F) having a core cross-section of at least:
1.5 mm² for cable lengths up to 25 m
2.5 mm² for cable lengths over 25 m
ON/OFF switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Press the green button on switch.
Restart protection in case of power failure
The device cuts off automatically in case of power failure.
To restart, push the green button
.
Switching off
Press the red button on switch.
Saw band selection
The saw band delivered by standard is suitable for wood and
most plastics.
Consider when selecting the saw band,
that no edgeless or damaged saw bands are used.
that the selection of the saw band and the number of
revolutions is suitable for the material to be cut.
Connect splinter extraction
In closed rooms work only with a splinter extraction
(air speeds at suction socket of the saw 20 m/sec.).
Sawing without splinter extraction only
for short-time service (up to 30 min.)
or with a protective mask
or open-air
If you do not connect splinter extractor sawdust will
concentrate which you have to remove regularly.
Connect sawdust extraction system or small dust extractor
with a suitable adapter to the sawdust suction socket (16).
Settings on the saw
Saw band tension
A too high stress can result in the break of the saw
band. A too less stress can result in the drive wheel
sliding through and then result in the stop of the saw
band.
You can check the stress:
Put the saw band coping (11) completely upwards (see
„Adjustment of the saw coping” page 20) and press with
the finger in the middle between the saw table and the
upper saw coping transversally against the saw band
it shall only be possible to push the saw band in
laterally by 1 – 2 mm.
With the adjusting wheel (1) the stress of the saw band
can be corrected.
Increase stress (+)
turn adjusting wheel clockwise
Reduce stress (-)
turn the adjusting wheel anti-clockwise.
Incline of the upper band saw roll
Open the upper case door (2) to be able to check the run
of the saw band by turning the band saw roll (13) manually
and clockwise.
With the adjusting wheel (20) the incline of the upper band
saw roll (13) can be changed. The adjusting causes that
the saw band runs in the centre of the band saw roll.
Before adjusting release the fixation nut (H).
Saw band runs backwards (+)
turn the adjusting wheel clockwise
Saw band runs forwards (-)
turn the adjusting wheel anti-clockwise
After adjusting refasten the fixation nut (H).
Transverse adjustment of saw table
Loosen the fixing screws (C / D).
The saw table (6) can continuously be inclined against the
saw band up to 45°.
Retighten the fixing screws.
Parallel stopper
The parallel stopper (8) is clamped on the saw table. It
can be assembled on the right or on the left of the saw
band.
Pay attention to the right adjustments of the parallel
stopper.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BS 205-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BS 205-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atika BS 205-2

Atika BS 205-2 Installation Guide - English, German, Dutch, Danish, French, Italian, Polish, Swedish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info