475723
26
Zoom out
Zoom in
Previous page
1/135
Next page
 Hold the file at right angles (90°) to the guide bar when
sharpening.
26
Â
ng angle the
Â
Using the round file and the correct sharpeni
correct breast angle β will result.
Â
The planing tooth lengthes (a) must be equal. Unequal
lengthes may lead to erratic chain run or chain breaking.
sharp, but it will possibly not cut. There must be always
a depth gaug
Once all sharpening angles are filed your saw chain is
e distance (T = distance between depth
gauge and cutting edge).
L Use a flat file to file the depth gauge distance.
Be sure to chamfer the leading edge of your depth
limiter with a file. The original shape of the cutting link
must be preserved.
L Only remove a little amount of material when
sharpening.
electric shar
You can also sharpen your saw chain yourself by using our
pener KSG 220 (article-no.: 302360).
Cleaning of guide bar
 / Â
Check and clean the oil outlets (A) of the guide bar and the
guiding groove (B) on a regular basis.
Remove any burr using a flat file.
Turn round the guide b
sharpening to avoid single
ar after each chain exchange /
-side wearing.
Immediately replace a damaged guide bar.
L
Chain wheel
The demand of the chain wheel is particularly great. Check
ularly the teeth of the chain wheel for wear
reg or damages.
Â
Clean the chain wheel (18) and the guide bar fixing
device using a brush.
amaged chain wheel reduces the durability
chain and should therefore immediately be
L A worn or d
of the saw
exchanged by the customer service.
Cleaning the air filter
- sta
loss of output,
erating hours, or more frequently in
Clean the air filter from dust and dirt on a regular basis to
prevent
rting problems,
-
- too high fuel consumption.
lean the air filter every 8 op
C
dusty environments.
Â
1. Open the air filter cover (21).
ir filter (22).
with a clean cloth to prevent dirt
Wash the air filter in a luke warm soapy solution.
2. Remove the a
3. Cover the intake opening
from coming into the carburettor.
4. Pull apart the both parts of the air filter.
5.
Do not puff/blow out dirt particles, otherwise there is a
replaced without
risk of eye injury.
6. Allow the air filter to dry well and reinsert it.
L Damaged air filters must be
delay.
Checking / Replacing the fuel filter
Â
chain saw is equipped with a fuel filter. Check it regularly
or repla
The
nd clean ce it if required.
lly pull it from the
clean it using petroleum ether.
a
For this open the tank cap (9) and pull out the fuel filter (10).
If the filter is only slightly contaminated, carefu
oil li andne
L If it shows a great extent of contamination, replace the
fuel filter.
Checking / Replacing the spark plug
- Do not touch the spark plug or the spark plug
connector while the engine is running. High voltage!
- Risk of
burning on the hot engine.
- Wear protective gloves.
ular basis.
For this
Check the spark plug and the spark gap on a reg
proceed as follows:
Â
Op
Â
en the air filter cover (21).
Pull the spark plug connector (23) from the spark plug
( g using the supplied wrench
24). Remove the spark plu
(36).
Â
The spark gap must be 0.6 to 0.7 mm.
Clean the spark plug when it is contaminated.
e order.
Install the spark plug in revers
Do not overtighten the spark plug.
the spark plug:
Replace
ever case comes
fi
- wh
- when the electrodes show excessive erosion,
- when the electrodes show excessive dirt or oil.
GON OPR15Y
RCJ7Y
- ery 100 hours or once in a year (which
rs
ev
t)
en the insulating body is damaged,
Use the following spark plug type: NGK-BPMR7A
BOSCH WSR6F
ORE
CHAMPION
Checking the ignition spark
against the engine body (away from the spark plug hole).
sition
1. Remove the spark plug (24).
2. Firmly connect the spark plug connector (23).
3. Use an insulated pair of tongs to press the spark plug
4. Put the ON/OFF switch to the po
.
ectrodes, the
spark plug may be defective.
5. Pull the cranking rope.
L If there is no spark visible between the el
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BKS 38 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BKS 38 A in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info