520730

Atika ASP 8 N - 400 Manual

27
Zoom out
Zoom in
Previous page
1/146
Next page
26
T
T
e
e
c
c
h
h
n
n
i
i
c
c
a
a
l
l
d
d
a
a
t
t
a
a
Model / Type ASP 8 N – 400
Splitting force 80 kN (8 t)
Log length max. 1050 mm
Log diameter min. 50 mm – max. 350 mm
Stroke
≈ 500 mm
Feed speed approx. 0.04 m/sek.
Return speed approx. 0.15 m/sek.
Hydraulic oil (max.) 5 litres
Hydraulic pressure 26 MPa (260 bar)
Electric motor performance (power consumption) P
1
3.0 kW (S6 40%)
Power supply 400 V 3~ 50 Hz, 16 A
Dimensions length 770 x width 540 x height 1520 mm
Weight approx. 104 kg
P
P
o
o
s
s
s
s
i
i
b
b
l
l
e
e
p
p
r
r
o
o
b
b
l
l
e
e
m
m
s
s
Before each fault clearance:
− switch off device
− pull out main plug
Problem Possible cause Remedy
Logs are not being split
properly
(insufficient splitting
performance).
⇒ The log is not positioned correctly.
⇒ The log exceeds the maximum dimensions or
the wood is too hard for the performance of
the machine.
⇒ Splitting blade does not split log.
⇒ Hydraulic pressure too low.
⇒ Release rods bent (hydraulic tappet not quite
pressed in).
⇒ Incorrect connecting lead (longer than 10 m or
too small cable cross-section).
⇒ Reposition the log correctly.
⇒ Cut the log to the required dimensions.
⇒ Sharpen splitting blade, check for burrs or notches.
⇒ Check the oil level and add more oil if necessary.
If the problem cannot be rectified, refer to the
manufacturer or other approved service centre.
⇒ Arrange for manufacturer or authorised company to
adjust the rods.
⇒ Use the correct connecting lead.
Splitting column moves
unsteadily or with strong
vibrations.
⇒ Air in the circuit.
⇒ Splitting column not sufficiently lubricated or
oiled.
⇒ Check the oil level and add more oil if necessary.
⇒ Lubricate splitting column or oil with environmentally
friendly spray oil.
If the problem cannot be rectified, refer to the
manufacturer or other approved service centre.
Splitting column does not
move in.
⇒ Hydraulic pump defective. ⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
Motor starts, but splitting
column does not move in.
⇒ Motor turns in wrong direction ⇒ Check the motor direction
Threephase: adjust the motor direction
Motor will not start.
⇒ No electrical power.
⇒ 2-phase mode in threephase motor.
⇒ Connection cable defective.
⇒ Electric motor defective.
⇒ Check the fuse.
⇒ Have fuse and lead checked by qualified electrician.
⇒ Replace the connection cable or have it checked by an
electrician.
⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
G
G
u
u
a
a
r
r
a
a
n
n
t
t
e
e
e
e
Please observe the enclosed terms of guarantee.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ASP 8 N - 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 8 N - 400 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info