520730

Atika ASP 8 N - 400 Manual

26
Zoom out
Zoom in
Previous page
1/146
Next page
Sharpening the splitting blade
After longer operating periods, for reduced splitting performance
or slight deformation of the cutting edge, grind the splitting blade
or sharpen it with a fine file (remove burrs).
25
How do I check the oil level?
1. The splitting column
must be in run-in state.
Now remove the dipstick.
2. Clean the dipstick and
the oil seal.
3. Replace the dipstick fully
into the oil reservoir.
4. Now remove the dipstick
again and read off the oil
level.
If the oil level is between the two marking on the oil dipstick,
there is sufficient oil in the reservoir.
If the oil level is below the lower marking, more oil should be
added with the aid of a clean funnel.
6. Check the oil seal and replace it if it is damaged in any way.
7. Replace the dipstick into the oil reservoir.
When should I change the oil?
The first oil change should be carried out after 50 operating
hours, and then every 500 operating hours.
Two persons are required for this.
Changing the oil:
1. The splitting column must be in run-in state.
2. Now remove the dipstick.
3. Place a container under the log splitter to catch the old oil.
The container should have a capacity of at least 5 litres.
4. Screw off the drain plug to allow the oil to flow out.
Sharpen wedges
drain plug
Oil dipstick
5. Insert the seal and drain plug again.
6. Pour in the new hydraulic oil (approx. 2 litres) using a clean
funnel.
7. Clean the dipstick and the oil seal.
8. Check the oil seal and replace it if it is damaged in any way.
9. Replace the dipstick.
upper marking
Dispose of the old oil properly (local oil disposal point). The
old oil must not be poured into the ground or drainage
system, or mixed with other waste.
L Hydraulic oil
lower marking
We recommend the following hydraulic oils for the hydraulic
cylinder:
¾ Shell Tellus T 22
¾ Aral Vitam Gf 22
¾ BP Energol HLP 22
¾ Mobil DTE 11
¾ or equivalent
Do not use any other types of oil. The use of any other type
of oil will adversely affect the operation of the hydraulic
cylinder.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ASP 8 N - 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 8 N - 400 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info