520730

Atika ASP 8 N - 400 Manual

25
Zoom out
Zoom in
Previous page
1/146
Next page
Adjusting the splitting cross:
1. Loosen star grip
screw.
2. Move the splitting
cross to the
correct position
(The star grip
screw is beyond
the borehole in the
splitting blade).
3. Mount star grip
screw.
24
Splitting short wood:
1. Upper position of table plate.
2. Place the log on the splitter’s table plate.
3. Hold the log tight with the clamping claws.
L Only split the logs in the direction of the wood fibres.
Splitting long wood:
1. Middle or low
position of table or
base.
2. Remove the splitting
cross.
3. Place the log on the
splitter’s table.
LPossible malfunction
when cleaving logs:
The
log to be cleaved is not
cleaved right through,
jams on the cleaving
blade and is pulled up
during the blade’s return
movement.
In this case, proceed as
follows:
1. Switch off the
device.
2. Depending on the
log still to be cleaved
fix the table plate in
the middle or upper
position.
3. Switch on the device
and continue the
splitting operation.
Never try to split
two logs at once.
Never try to remove
or replace the log during
the splitting process.
L Never try to force the splitting of the log by maintaining the
pressure for several seconds. This can lead to damage to the
machine.
Star grip screw
Splitting cross
Position the log on the table again and repeat the splitting phase,
or put the log on one side.
How to release a jammed log?
There is a risk of knotted logs getting stuck during the splitting
process.
1. Switch machine off and disconnect the power.
2. Do not remove jammed logs with your hands.
3. Carefully move the stuck log with a crowbar backwards and
forwards to loosen it. Don´t damage the splitting pillar.
Never hammer on the stuck log.
Never use a saw to cut the stuck log out of the machine.
Do not enlist the aid of a second person - this is a one-
man job.
Finishing work:
¾ Bring the splitting blade to the lower position (run-in state).
¾ Release one of the control handles.
¾ Switch the machine off and disconnect the power.
¾ Follow the care and maintenance instructions.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work:
− switch off device
− pull out main plug
Wear protective gloves in order to avoid injury to the
hands.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Be sure to have removed any tools from the machine after
completion of service work.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
L Observe the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have finished
using it.
Loose fastening elements.
Worn out or damaged parts.
Remove any resin remains on the machine.
Lubricate the splitting column regularly or oil it using
environmentally friendly spray oil.
Check hydraulic hoses and hose connections regularly
for any leaks and firm fitting.
Correct assembly and faultless covers and protective
devices.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ASP 8 N - 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 8 N - 400 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info