519276

Atika ADH 204 Manual

21
Zoom out
Zoom in
Previous page
1/53
Next page
20
If there is a power cut, the machine switches off
automatically. Push the green ( I ) button to start the
machine again.
Switching off
Press the red button on the hinged cover.
Motor protection
The motor is equipped with a safety switch and switches
off automatically when overloaded.
It can be switched back on following a cooling off phase
(5 – 10 min).
Press the
1. red button ( 0 ).
2. the small button next to the button (8)
3. the green button ( I ) to start
Dust / chip exhaustion
The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
Connect therefore always a chip exhaust system or small
vacuum cleaner with suitable adapter to the chip exhaust neck
(31) (Ø 100 mm).
Make sure that the shavings extractor is properly earthed.
L Velocity of air on the extractor connector on the machine
≥ 20 m/sec.
L The motor will only start if the extractor hood (29) is
properly attached and thus releases the safety switch.
Working instructions
Before starting to work consider the following safety
advices to keep the risk of injuries as small as
possible.
Workplace tidied?
Is the surface planing and thicknessing machine securely
installed?
Are all fastening screws tightened?
Is the blade securely fastened on the blade shaft?
Are the pushing bars handy?
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Also, note the following important points:
When machining make sure that the unused blade shaft is
covered by the knife guard.
Place yourself outside of the area of danger.
Place your hands flat on the workpiece with fingers closed.
Never remove loose splinters, chips, or similar by hand.
Connect a dust or shavings extractor.
Make sure that the feed rollers and cutting tools are free
from wood shavings and dust.
Do only machine workpieces the dimensions of which are
within the specifications for this machine (see “Technical
data” on page 26).
Do not guide back the workpiece over the open-running
blade shaft.
Adjust the smallest cutting depth after your work is finished.
Ensure that you always comply with the safety
instructions given on p. 17
Surface planing
The objective of surface planing is to smooth a rough surface
(planing), e.g. to smooth the edge of a board.
For this the workpiece is placed onto the feed table plate and is
machined on its underside. Feed direction is from right to left. L
Preparations
Pull the mains plug before performing
settings.
Installing the dust extractor
1. Place the crank handle (15) onto the shaft end on the table
plate and turn it anticlockwisely to bring the thicknessing
table plate to its lowest position. F
2. Place the extractor hood (29) onto the thicknessing table
plate. Make sure that the both stop pins engage in the holes
of the thicknessing table plate. G
3. Turn the crank handle (15) clockwisely until the extractor
hood (29) is securely clamped by the thicknessing table
plate.
4. Fix the extractor hood using the nut M6 and a washer A 6.4.
H
5. Remove the crank handle (15).
6. Push the extractor connector (31) on the extractor hood.
7. Connect the shavings extractor with the extractor connector
(31).
Planing and joining workpieces
Adjusting the guide plate (1) I - J
1. Loosen the locking lever (21).
If you can not sufficiently turn the locking lever, pull out the
lever head and turn it back.
2. Tilt the guide plate to your desired angle which you can read
from the angle scale (22).
3. Tighten the locking lever (21) again.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ADH 204 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ADH 204 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info