519276

Atika ADH 204 Manual

19
Zoom out
Zoom in
Previous page
1/53
Next page
18
Wear suitable work clothes:
− Do not wear loose-fitting clothes or jewellery; they can
catch in moving parts.
− slip-proof shoes
− Hairnet in case of long hair
Wear protective clothing:
− ear protection (Sound intensity level at workplace can
exceed 85 dB (A))
− safety goggles
− Dust mask with work activities generating dust
− Gloves for blade exchange.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Take into consideration environmental influences:
− Do not expose this surface planing and thicknessing
machine to rain.
− Do not use the equipment in a damp or wet environment.
− Do only work with sufficient visibility conditions. Provide
for good illumination.
− Do not use this machine near inflammable liquids or
gases.
− The wood dust generated during operation impedes the
necessary view and is harmful to health to some
degree. Connect this machine to a dust or shavings
extractor (e.g. small portable deduster).
Never leave the machine unattended.
Persons under the age of 18 must not operate the device.
Keep other persons away.
Do not allow other persons, especially children, to touch
the tool or cable.
Keep them away from your working area.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Assume the correct work posture. Stand to the side of the
machine.
While the machine runs keep your hands at a safe distance
from the blade shaft and the location where shavings are
ejected.
Always keep sufficient distance to the blade shaft. Maintain
sufficient distance from driven components during operation.
Remove all nails and metallic objects from the work piece
before planing or thicknessing.
Pay attention that the work piece does not contain any
cables, ropes, cords or the like.
Do not machine wood which has numerous knots and knot
holes.
Only start planing and thicknessing when the blade shaft has
reached its required speed.
Use only well sharpened blades as edgeless blades
increase not only the risk of backstrokes but also charge
the motor.
Use appropriate devices when machining thin work pieces to
position and guide the wood pieces properly.
When machining make sure that the unused blade shaft is
covered by the knife guard.
Do only use tools according to EN 847-1 which are marked
with MAN.
The use of other tools and other accessories can
signify a risk of injury for you.
Use pushing blocks or bars when machining short work
pieces.
Do not use defective pushing blocks or bars
Always keep the pushing blocks and bars handy at the
machine if they are not used.
Secure long workpieces against dropping down when
finishing the cutting process.
Use roller supports or similar
devices for this purpose.
Do not remove splinters, shavings and waste with your
hands from the dangerous area of the blade shaft.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− maintenance and cleaning
− Fault elimination (this also includes removing of jammed
shavings or splinters)
− checks of connecting lines, whether these are knotted or
damaged
− Transporting the machine
− Changing the blades
− leaving the machine unattended (even during short
interruptions)
Maintain your machine with care:
− Keep your tools sharp and clean in order to be able to
work better and safer.
− Follow the maintenance instructions and the
instructions for tool exchange.
− Keep handles dry and free of oil and grease.
Check the machine for possible damage:
− Before further use of the machine the protection
devices or slightly damaged parts must be checked
carefully for their proper and intended function.
− Check whether the movable parts function perfectly and
do not stick or whether the parts are damaged. All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation of the machine.
− Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
− Damaged or illegible safety labels should be replaced
immediately.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and
adjusting tools are removed.
Store unused equipment in a dry, locked place out of the
reach of children.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ADH 204 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ADH 204 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info