Manual Atika ADH 204 (page 22 of 53) (English, German, Dutch, French)

519276

Zoom out

Zoom in

1/53

Adjusting the depth of cut K

1. Turn the adjusting screw for the depth of cut (4)

2. You can read it from the depth of cut scale (3).

Adjusting the blade shaft guard

1. Push the workpiece against the guide plate.

2. Loosen the clamping screw for the blade shaft guard (16)

3. For flat workpieces (< 75 mm): L

Push the blade shaft guard (12) against the guide plate (1)

and lift it according to the workpiece thickness.

Push the workpiece somewhat below the blade shaft guard

and lower the latter onto the workpiece.

4. For high workpieces (> 75 mm): M

Lower the blade shaft guard down to the table plate and

push it against the workpiece.

Planing

1. Start the motor.

2. Push the workpiece right-angled over the feed table plate. N

3. Hold your fingers close to each other and guide the

workpiece with flat hands or with pushing bars over the feed

table plate.

4. When planing narrow surfaces (joining edges) push the

workpiece with both hands and clenched fists against the

guide plate and the table plate and push it over the feed

table plate. O

5. When planing and joining short workpieces use the pushing

block (27) P

6. Press down the workpiece only on the delivery table.

7. Turn the machine off if the work is not immediately

continued.

Skewing Q

1. Place the workpiece against the tilted guide plate.

2. Adjust the blade shaft guard so that it just contacts the

workpiece and tighten the clamping screw for the blade shaft

guard.

3. With your left clenched fist press the workpiece against the

guide plate and the delivery table plate. Push the workpiece

with your closed right hand over the feed table plate.

4. Turn the machine off if the work is not immediately

continued.

Thicknessing

The purpose of thicknessing is to make the workpiece with

already planed surface thinner.

For this the workpiece is guided through the machine and

machined on its top surface.

The already planed surface faces

the thicknessing table plate.

The feed direction is exactly the

other way round as for planing from left to right.

L When thicknessing a step will be formed on the lead and

tail edges of the workpieces. Therefore cut the workpiece

to length only after thicknessing

Preparation

Pull the mains plug before performing

settings.

Installing the dust extractor R

1. Loosen the clamping screw (16) and push the blade shaft

guard off from the table plate.

2. Adjust the guide plate (1) to 45°.

3. Place the extractor hood (29) onto the planing plate. Make

sure that the both star grip screws (30) are aligned with the

holes in the planing plate.

4. Tighten the star grip screws (30). Make sure that the contact

for the safety switch (28) rests on the safety switch.

5. Push the extractor connector (31) on the extractor hood.

6. Connect the shavings extractor with the extractor connector.

Thicknessing S

1. Adjust the depth of cut. F

L In a single pass the machine can cut 2 mm as a

maximum. However do only adjust this depth if:

- your blades are very sharp,

- you machine soft wood types,

- you machine workpieces the width of which is

smaller than the maximum width.

2. Start the motor.

3. Push in the workpiece slowly and right-angled in arrow

direction. It will be drawn in automatically.

4. Guide the workpiece straight through the machine.

5. Turn the machine off if the work is not immediately

continued.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Atika ADH 204 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Atika ADH 204 Manual

Product: