76319

ATAG KD 8122 BF Manual

20
Zoom out
Zoom in
Previous page
1/35
Next page
20
* Depending on model and options
children) with reduced physical, sensory or mental ca-
pabilities or lack of experience and knowledge unless
they have been given initial supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that
they do not play with the appliance.
W Avoid prolonged skin contact with cold surfaces or chilled/frozen
food. This could cause pain, numbness and frostbite. In the
case of prolonged skin contact, protective measures should
be taken, e.g. gloves should be worn.
W Do not eat ice cream, particularly ice lollies or ice cubes, imme-
diately after taking them from the freezer compartment as there
is a risk of "burning" because of the very cold temperatures.
W Do not consume food which has been stored for too long, as it
could cause food poisoning.
Installation and ventilation information
W Avoid positioning in direct sunlight or next to an oven,
radiator or similar.
W Do not block the ventilation areas. Always
ensure that the appliance is properly venti-
lated.
Condensation may form on the outside of the
refrigerator/freezer during periods of high
humidity.
Constant ventilation of the installation site is recom-
mend.
W Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m
3
per 8 g of R 600a
refrigerant used in the appliance, so as to avoid the formation
of inflammable gas/air mixtures in the room where the appli-
ance is located in the event of a leak in the refrigerant circuit.
The quantity of refrigerant used in your appliance is indicated
on the type plate on the inside of the appliance.
W Only install the refrigerator/freezer in stable furniture.
W Please follow the enclosed installation instructions.
Operation and control elements
You are advised to clean the appliance before switching it on for
the first time (see "Cleaning").
If your appliance has a freezer compartment, switch it on approx. 2
hours before filling the freezer with frozen food for the first time.
Connecting to the mains
Power supply (AC) and voltage
at the operating point must comply with the details on the
type plate. The type plate is located on the inside left of
the appliance, fig.
A.
W The appliance must be connected with a properly
installed fused socket.
W The socket must have a 10 A fuse or higher. It must be away
from the back of the appliance and easily accessible.
W Do not
- connect to stand-alone inverters and
- operate with so-called energy-saving plugs - this can damage
the electronic system,
- connect to the supply with other electrical equipment using a
distributor strip or an extension cable - risk of overheating or
fire.
W When removing the mains cable from the back of the appliance,
remove the
cable holder to prevent vibration noise.
The wires in the mains lead are coloured in accordance with the fol-
lowing code: green/yellow = earth, blue = neutral, brown = live.
Warning! This appliance must be earthed.
Non-rewireable plugs BS 1363
If this machine or appliance is fitted with a non-rewireable plug, the
following information applies: If the socket outlets are not suitable
for the plug supplied with this product, it must be cut off and an
appropriate plug fitted. The plug cut from the flexible cord should
be disposed of and on no account be inserted into a 13 A socket
elsewhere in the house (electric shock hazard).
The fuse cover must be re-fitted when changing the fuse, and if the
fuse cover is lost the plug must not be used until a suitable replace-
ment is obtained. The colour of the correct replacement cover is
that of the coloured insert in the base of the plug, or the colour that
is embossed in words on the base of the plug (as applicable to the
design of the plug fitted). The correct rating of the replacement fuses
that are ASTA approved to BS 1362 should be fitted. Replacement
fuse covers may be purchased from your local electrical suppliers,
electricity showroom or approved service agent.
Switching the appliance on and off
W To switch on: Press the on/off button 3 so that the tempera-
ture display lights up or flashes.
- The lighting will light up when the door is open.
W To switch off: Press the on/off button for approx. two seconds
so that the temperature display goes out.
Notes on energy saving
W Ensure that there is adequate space around the ap-
pliance for ventilation and air extraction.
W Avoid keeping the door open for too long.
W Store food logically. Do not exceed the storage period speci-
fied.
W Keep all food properly packed and covered so as to avoid its
frosting up on the outside.
W Always allow hot food to cool to room temperature before plac-
ing in the appliance.
W Defrost frozen food in the refrigerator.
W If an ice layer forms in the freezer compartment*, you should
defrost it. This will improve the cold transfer and reduce energy
consumption.
!
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG KD 8122 BF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG KD 8122 BF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info