Manual Astralpool OPTIMA 15 (page 20 of 75) (English, Portuguese, Spanish)

673148

Zoom out

Zoom in

1/75

ENGLISH

6. HIBERNATION PROCEDURE

1. Switch off the filtering pump.

2. Turn off valves 2 and 3 of the by-pass.

3. Open completely valve 1.

4. Drain the exchanger to protect it from ice, disassembling the inlet and outlet connectors of the heat pump.

5. Once drained part of the condenser, assemble the connectors.

6. Check the connectors of the heat pump to restrict the entrance of foreign bodies to the exchanger.

7. MAINTENANCE INSTRUCTIONS

Installation and maintenance

 In the event of any intervention in the unit, installation, start-up or maintenance, the personnel in charge of these

operations must be familiar with both the instructions and recommendations contained in the installation manual

and the elements of the project.

 The personnel in charge of the receipt of the unit will perform a visual inspection in order to verify the possible

damages suffered in the transport: refrigeration circuit, electrical cabinet, frame and housing.

 It is prohibited to place the unit near:

Heat sources Flammable materials · Building air intakes

 The unit must de installed, started-up, repaired and maintained by qualified personnel according to applicable

regulations and laws.

 During installation, repairs and maintenance piping should not be tread on or used as a support, otherwise the

piping could break and the R-407-C gas could cause severe burns.

 During maintenance of the unit, the composition and state of the gas will be revised as well as possible oil

stains (leaks in the refrigeration circuit).

 During the annual maintenance revision of circuit water tightness according to regulations, verify that the high-

pressure and low-pressure controllers are properly connected to the refrigeration circuit and that they switch off

the electrical circuit in case of failure.

 In the event of any manipulation or intervention on the refrigeration circuit, it is obligatory to switch off the unit

and wait several minutes before puncturing pressure gauges or measuring temperatures. Some elements such

as the compressor and pipes can reach high temperatures and high pressures that can lead to important burns.

 Never add oil to the unit; the compressor is loaded with specific oil, polyol ester (POE) that does not tolerate the

presence of other types of oil.

 The instruments used for the load, pressure measurement, creation of a vacuum and recovery of the liquid must

be compatible and be only used for the R 407 C liquid.

 The weight of the coolant contained in the storage deposit must be constantly verified. If the remaining weight is

lower than 10% of the gross weight, do not use it.

 In the event of a new charge:

-Do not use the load cylinder

-Use a balance and a bottle of R 407 C with an immersion tube

-Load the weight of R 407 C following the value indicated in the plate where the characteristics of the

unit are specified.

-The load must be done in liquid phase.

 In case of leaks, do not complete the load: recover the remaining liquid for its recycling and carry out a full load

again. The recovery, recycling or destruction of liquid should always be carried out in accordance with the

applicable laws in each country.

 If the refrigeration circuit is open, the following tasks must be carried out:

-Minimize the entrance of ambient air in the circuit

-Replace the dehydrator.

-Carry out the “creation of a vacuum” to a minimum level of 0.3 mbar (static).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Astralpool OPTIMA 15 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Astralpool OPTIMA 15 Manual

Product: