632824
4
Zoom out
Zoom in
Previous page
1/8
Next page
2
PARTS IDENTIFICATION
Open & Close
Safety-Lock Buttons
Lid Grip
Pressure
Control
Locking
Lid
Induction-Ready
Stainless Steel Bottom
Pressure Valve (A)
Washer (B)
Nut (C)
Pressure Control Assembly
Pressure Level SettingsSilicon Ring & Safety Vent
Cool-Touch
Handles
Float Valve
Pressure
Cooker Pot
1
2
Pressure Level Settings
=
Low Pressure
8.7 PSI
High Pressure
13.1 PSI
No Pressure
0 PSI
A
B
C
11
TROUBLESHOOTING
The Float Valve won’t rise when cooking with the pressure cooker.
It will take a few moments for pressure to build up and for the Float Valve to begin rising. If
after a few minutes of heating, the valve still isn’t rising, it could be due to one or more of the
following reasons:
1. The temperature may not be high enough. Increase the temperature of the heat source.
2. There isn’t enough liquid in the Pressure Cooker Pot. The amount of liquid in the pot
should at least be up to the “MIN. 1/3” marking inside the pot.
3. The Pressure Control is set to “ ” and therefore not building pressure. The Pressure
Control must be set to “1” or “2” in order to build pressure.
4. The Locking Lid is not properly locked in place. Ensure the lid is securely locked
onto the Pressure Cooker Pot.
5. The Float Valve is clogged with debris and needs to be cleaned. Using caution to avoid
escaping steam, set the Pressure Control to “ ” to quickly release the inside pressure.
Once the pressure has been released and the pressure cooker is completely cool, remove
the Locking Lid and clean the Float Valve of any debris. Without placing the Locking Lid
on the Pressure Cooker Pot, press the “CLOSE” button on the lid to test if the Float Valve
can move freely. Gently press on the back of the Float Valve beneath the Locking Lid to
ensure it rises up and down freely.
6. The Silicon Ring is damaged, not in place or the edge of the Pressure Cooker Pot is
damaged. If the ring or pot is damaged, DO NOT attempt to use the pressure cooker and
contact Aroma customer service at 1-800-276-6286, Monday to Friday 8:30AM-4:30PM
PST or via e-mail at CustomerService@AromaCo.com.
The Float Valve rises but no steam is emitting from the Pressure Valve
Stop heating the pressure cooker and allow it to cool completely. Once cool, check the
Pressure Valve and Float Valve to make sure they are clean and completely free of debris.
The Locking Lid cannot be unlocked and opened.
Check whether the Float Valve has fallen completely. If not, allow the pressure cooker to cool
further. NEVER force the Locking Lid off of the Pressure Cooker Pot and always use
caution to avoid escaping steam.
There is excessive steam coming from the rim of the Pressure Cooker Pot.
This can result from one or more of the following reasons:
1. The Locking Lid is not properly attached to the Pressure Cooker Pot. Check to make sure
the lid is properly locked in place.
2. The Pressure Cooker Pot is overfi lled with liquid and ingredients. Make sure the liquid and
all ingredients never exceed the “MAX. 2/3” marking inside the pot.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aroma APC-600S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aroma APC-600S in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info