566471

Ariston NUOS 200 SPLIT Manual

35
Zoom out
Zoom in
Previous page
1/104
Next page
Heat pump water heater – INSTALLATION
35
4. INSTALLATION
WARNING! Observe the general warnings and safety instructions listed in the previous
paragraphs and strictly adhere to the indications therein contained.
4.1 Location of the internal unit
WARNING! Prior to starting any installation activities, ensure that the location where the water heater is to be
installed satisfies the following requirements:
a) Respect the Minimum installation dimensions specified in Figure 5,
b) Avoid installing the appliance in rooms which may favour frost build-up. The product is designed for
indoor installations, the product’s safety and performance levels are not guaranteed in the event of
outdoor installation.
c) Ensure that the installation site and the electrical and hydraulic systems to which the appliance must be
connected fully comply with the regulations in force.
d) The chosen site must have, or must be suitable to house, a single-phase 220-230 V ~ 50 Hz power
supply socket.
e) The support surface must ensure a perfectly horizontal operating position, and can withstand the weight
of the water heater filled with water.
f) The chosen site must conform to the appliance’s IP protection rating (protection against the penetration of
liquids) as specified by the regulations in force.
g) The appliance must not be exposed to direct sunlight, even when windows are present.
h) The appliance must not be exposed to particularly aggressive substances such as acidic vapours, dust or
gas-filled environments.
i) The appliance must not be directly installed on lines that are unprotected against overvoltage.
j) The appliance must be installed as close as possible to the points of use to limit heat dispersion along the
piping.
Positioning on the ground – 300 litres floor standing model
a) Once the suitable installation position has been located, remove the packaging and remove the fixings
visible on the pallet where the product is based (fig.6).
b) Fix the feet on the ground (through the appropriate holes) using suitable screws and rawlplugs.
Positioning on the ground – 150-200 litres wall hung model
a) Fix the product through the brackets on a bearing wall, using the installation template printed on the
packaging. For each bracket using two bolts,and two chrome screws concrete type Fischer M10, M12 or
M14, No. 2 nuts M10, M12 or M14, No. 2 washers M10, M12 or M14. Make sure the screws and bolts are
tight. (see Figure 7).
b) This model can be installed on a support tripod only use the appropriate model provided by the
manufacturer of the water heater. In this case the product must be secured to a bearing wall over
the upper bracket, or both.
4.2 Location of the external unit
WARNING! Prior to starting any installation activities, ensure that the location where the water heater is to be
installed satisfies the following requirements:
a) establish the most suitable position on the wall, allowing enough room to easily perform any maintenance
(see fig. 3);
b) Install the outdoor unit on a solid wall in a very secure way, in a place where noise and exhaust air do not
cause trouble. Choose a place that does not obstruct the free passage and which is easy to evacuate the
condensate produced.
c) The plan of operation must be exactly horizontal, check with a level (Fig. 3).
d) Follow the steps and only then start making the connections of the pipes and electric cables;
e) secure the brackets to the wall using suitable fixings for the wall (be careful to cables and pipes in the
wall), use dowels larger than the weight would require: while operating the machine vibrates and must be
installed for years without any screw come loose.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston NUOS 200 SPLIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston NUOS 200 SPLIT in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info