160350
19
Zoom out
Zoom in
Previous page
1/30
Next page
E-19
movie 2.1
solo
English
Audio set-up
This section allows you to configure the analogue,
digital and HDMI audio outputs. In particular, the digital
output type needs to be set correctly if you are using an
external audio decoder, receiver or D-A converter.
Digital audio output
This setting configures the digital audio output – coaxial,
optical and HDMI.
Stereo PCM When ‘Stereo PCM’ digital output is selected, all
audio material played is down-mixed to stereo
and output as stereo PCM. Use this setting if you
have an external D-A converter that supports
only two-channel PCM.
Bitstream The Bitstream setting supports the following
audio standards:
<
2 channel PCM (on CDs or DVDs)
<
Dolby Digital
<
MPEG multi channel (not available in HDMI)
<
DTS multi channel
Use this setting if you have a receiver/decoder
that supports Dolby Digital.
HDMI (Auto) This setting means that the HDMI sink (display)
device takes control of the audio setting, with
the Solo 2.1 sending audio in a suitable format.
DVD sample rate
This needs to be set correctly if you are using an external
audio decoder, receiver or D-A converter connected to
the S/PDIF digital audio output.
Max 48k Choose this option if your external audio
decoder is unable to process digital audio with
a sample rate above 48kHz. This is the normal
setting for this menu item.
Max 96k Choose this option if your external audio
decoder is able to process digital audio with
a sample rate of up to 96kHz, or if you are
not using the digital audio outputs. This is the
maximum sample rate present on DVD-video
discs.
Note that this setting is relevant only to the output from
DVD-video discs.
Audio compression
Allows compression of the audio stream to be turned on
or off, where ‘On’ is intended for ‘late night’ listening when
large volume changes are not desirable.
Turning compression on decreases the volume of the
louder passages, i.e., the total dynamic range of the audio
is reduced. Normally, however, this item is set to ‘Off, to
disable compression.
This menu option only affects analogue output: the
coaxial and optical digital audio outputs are never
affected by this menu setting.
Compression is available only on Dolby Digital
recordings.
VCD mode
Some VCD discs are produced with a dual-mono
soundtrack. This means that the left audio channel carries
one language, the right another. In this case it can be
useful to listen to just one of the channels.
Stereo The default setting. Choose this option to play the
VCD with both channels audible.
Left
channel
only
Choose this option to play the VCD with only
the left channel audible. The audio from the left
channel will be routed to both the left and right
speakers.
Right
channel
only
Choose this option to play the VCD with only the
right channel audible. The audio from the right
channel will be routed to both the left and right
speakers.
This setting applies only to VCD discs.
Zone 2/Rec out
This controls the output sent to the ZONE 2/REC OUT rear
panel connectors. If a second room system is used (‘Zone
2’), the output level may be controlled independently,
fixed at a certain volume level, or set at line level.
Zone 2
variable
Output level varies with the volume control for
the second room
Zone 2 fixed Output level is fixed at the level last selected in
‘Zone 2 variable’ mode.
Record out
This option takes the output before the volume
control and may be connected to a recording
device. Never use this setting with a
power amplifier connected.
SAT SCART Audio in/
AUX SCART Audio in/
AV SCART Audio in
If you prefer to inject the audio signal from a source
other than the SCART socket, these three controls
allow you to selectively disable the audio signal from the
SAT, AUX or AV SCART sockets respectively. The default
setting is that audio input is enabled.
Disabled SCART audio input ignored; RCA sockets used
for audio input
Enabled Take audio input from SCART socket
Cadence over-ride
This setting is used to correct motion artefacts with
poorly mastered DVDs. For instance a film image shot at
24 frames per second may be tagged (incorrectly) with a
video frame rate of 30.
Only over-ride the default setting if artefacts are present
on the picture and return Solo Movie 2.1 to the Auto
(Default) setting to view the next DVD. Cadence
over-ride also returns to ‘Auto’ after powering off (i.e.
switching to Clock mode).
Auto (Default) Use cadence setting tag on the DVD
Film Force cadence to film rate
Video Force cadence to video rate
SAT SCART switching/
AV SCART switching
These menu items indicate to the display if SCART
output is active or not, so that the display can switch to
its SCART input automatically. The options are ‘Auto’
the default, and ‘Forced’.
Forced Signals that SCART is active independently of
what is connected to Solo Movie 2.1.
Select this option if Composite input is used.
Auto
(SCART)
Signals that SCART is active, depending on
what is connected to Solo Movie 2.1. This is the
default option.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam solo movie 2 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam solo movie 2 1 in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam solo movie 2 1

Arcam solo movie 2 1 User Manual - German - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info