Manual Arcam DiVA AVR100 (page 11 of 17) (English, German, French)

578766

Zoom out

Zoom in

1/17

AVR100

English

VOLUME control

To adjust the volume level of the loudspeakers, pre-amp outputs

and headphones use the VOLUME control. The volume level is

shown in the display while it is being adjusted. Three seconds

after the volume is adjusted, the display reverts to show the

selected input.

Note that different sources may require different settings of the

VOLUME control to achieve the same perceived volume level.

The volume can be controlled from 0dB over 80 steps.

BASS and TREBLE controls

Turn the bass and treble controls clockwise to boost response

or anticlockwise to cut response. For a ﬂ at response leave the

controls in the 12 o’clock ‘notched’ position.

Pressing the

DIRECT button bypasses the bass and treble

controls and gives a small improvement to sound quality. If

you do not wish to alter the bass or treble controls, we

recommended that you select DIRECT.

MHz

STEREO

SPEAKERS

VIDEO 1

RDS INFO

FM MUTE/

MONO STORE

PRESET/

TUNE DOWN/UP

Tuning to a station

Pressing the PRESET/TUNE button toggles between the two

tuning modes of the unit – ‘Preset’ or ‘Tune’. The selected mode

is brieﬂ y shown in the display.

Preset mode

In Preset mode, press the

•

and

•

buttons on the front panel

(or P– or P+ on the remote control handset) to cycle up and

down the preset stations.

See ‘Storing a preset’ and ‘Deleting unused presets’, below.

Tune mode

In Tune mode:

■ Press the

•

and

•

buttons on the front panel (or P– or

P+ on the remote control handset) for longer than half-a-

second to engage automatic tuning. The tuner searches

for a radio station signal of sufﬁ cient strength and stops.

To skip to the next station, press one of the buttons

again. Automatic tuning is available for both the FM and

AM bands.

■ Tapping the

•

and

•

buttons engages manual tuning. This

can be used for tuning to a speciﬁ c frequency. It is also

useful if you are trying to select a station that is too weak

for the auto search mode.

Regardless of the mode used to tune your AVR100, when it is

accurately tuned to a station ‘

•

TUNED

•

’ lights up in the display.

Storing a preset

To store a preset, tune to the radio station you wish to store.

Press the STORE button: this causes ‘MEMORY’ to ﬂ ash in the

display. Now select the preset number you wish to assign to

the station using the

•

and

•

buttons on the front panel (or

P– or P+ on the remote control handset). Press the STORE

button again.

Once the preset is stored, the display reverts to show the

station name (if RDS information is transmitted) or its frequency.

To quit the memory function without storing a preset, leave the

tuner controls untouched for ten seconds. It is also possible to

overwrite a stored station by saving another in its place. There

are thirty presets available for FM use and ten for AM use.

Your presets are retained for several weeks (but not indeﬁ nitely),

when the AVR100 is disconnected from the mains supply.

Deleting an unused preset

Press the STORE button, then select the preset number you

want to delete using the

•

and

•

buttons (or P– or P+ on

the remote control handset), followed by the FM MUTE/MONO

button.

The display brieﬂ y shows ‘DELETED’ and ‘– –’ is shown in

place of the preset number. You can reactivate a deleted preset

number by storing a station in the normal way.

The AVR100’s radio tuner can be controlled from the upper row

of front panel buttons (see diagram, below) or from the remote

control handset (see ‘Using the remote control’).

Using the tuner

after 3 seconds

DOLBY PRO LOGIC SPEAKERS

VIDEO 1

CH dB

DOLBY PRO LOGIC SPEAKERS

VIDEO 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam DiVA AVR100 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam DiVA AVR100 Manual

Product: