3 red LEDs indicate the sound level of the received signal from the baby unit. The louder the sound, the more LEDs turn on.
2. Volume keys
Press the + button to increase the volume one level, it emits a short beep.
Press the - button to decrease the volume of a level when the volume reaches its maximum or minimum value, it beeps three times.
In total there are 9 volume levels.
3. ON / OFF - button
Press and hold the button for 2 seconds to turn power on or off.
4. Speaker
> Broadcasts the sound made by your baby.
> Connection warning: If the device is turned on and the connection between baby and parent units is lost, or if it can not
connect when turning the units on a continuous beep will be heard. Once the connection is restored, the beeping will stop.
> Battery warning signal: If the batteries are running low, the units will produce short beeps until batteries are replaced.
5. Power/Connection/Battery status/HEALTH DECT (LED green / red)
LED is green: Power is on and properly connected to the baby unit
LED flashes green fast: No connection with the baby unit
LED lights up red: The battery is dead and must be recharged
LED flashes red fast: The device is charged. The batteries will recharge when the device is connected to the mains power supply. The full charging time is approximately 8 hours.
LED flashes green slowly: HEALTH DECT activated to stop unnecessary radiation (30 seconds after starting the speaker it is turned off when this mode is enabled).
LED OFF: Unit is switched off
6. Power supply connector DC 6V
When connecting the power supply (TEN PAO S003IV0600050)
7. HEALTH DECT mode slide switch
There are 2 modes: HEALTH DECT (sound activation mode) or Continuous mode.
When the switch is set to „PERMANENT“, the two devices will be in continuous transmission mode.
When the switch is set to „HEALTH DECT“, the baby unit will operate in the standard sound-activated mode. This means the baby unit activates its radio transmission only after detecting a sound. If the baby unit detects no
sound, it will stop its radio transmission automatically after a few seconds.
8. Health DECT mode - Range check
When the slide switch is in HEALTH DECT mode and there is no sound, there will be no transmission between the units. This means that you should manually check the range again if you move the units further apart.
To test the range manually, you can press the paging button on the baby unit or move the slide switch on the parent unit to “PERMANENT”. We recommend not to charge the parent unit during the range check. Either after a
few seconds, a connection is established and the connection indicator is solid green or if the baby unit is not in range, an alarm is triggered. Please move the slide switch to HEALTH DECT mode again after the range check to
make sure that there will be no radio transmission between the units.
In PERMANENT mode range checking is done automatically.
9. Battery compartment cover
10. Power Supply
100-240V ~ 50/60Hz, 6V, 500mA, TEN PAO S003IV0600050
11. Batteries
2x ANSMANN NiMH type Micro AAA batteries, 1.2V, 550mAh (included)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Ansmann Sydney at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Ansmann Sydney in the language / languages: All languages as an attachment in your email.
The manual is 4,4 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
