> The baby / parent unit and the power supplies should not be placed near any heat sources (radiators, fireplace, stove, direct sunlight).
> The baby and the parent unit must be protected from moisture and humidity. Do not submerge units in water. Please keep the devices away from bathtubs, sinks or wet surfaces. Devices that have become wet should not
be used. If a unit becomes wet, please contact our customer service team.
> Place the units and power supply in a well ventilated area. This will protect all components from overheating.
> Do not use the units near fluorescent lighting or other electrical / optical electronic devices such as televisions, motors, computers, cordless DECT telephones etc. These devices can have a negative effect on the baby
phone system.
> Please only use the power supplies provided. These power supplies are intended for use in the home only.
> Please make sure that the voltage of the power supply matches the socket to be used and that the socket is physically compatible (see information about the mains power supplies).
> Connect the mains power supply to an easily accessible socket, out of the reach of children.
> Ensure the power cord is placed so that it presents no trip hazard, does not become entangled with other objects and it can not be reached by children. Please consider when placing the cable, the potential danger to
children of neck injuries or suffocation by strangulation.
> When operating, the devices will get slightly warm - this is absolutely normal.
> Always unplug the power supply or switch off the mains socket when not in use.
> When operating the parent unit on batteries please make sure the batteries are charged and fully functional. The charging status is displayed on an active device via LED lights.
> If the parent unit is being powered by mains, it will still work during power failure if the batteries still have charge left in them. It is advisable to check the batteries often to ensure they are still charged.
> Batteries should be replaced only by adults. Remove the lid of the parent unit and insert the batteries with correct polarity.
> If the batteries discharge very rapidly after turning the units on, they must be replaced. The average life span of battery is approximately 4 Years.
> Do not try to recharge non-rechargeable batteries as they can explode.
> This device is not suitable for the use of lithium batteries.
> Two ANSMANN NiMH 1.2V, 550mAh AAA batteries are included. Please make sure these are inserted using the correct polarity.
> Do not use two different types of battery in the baby phone units
> Please ensure any tools are out of reach of children when changing the batteries
> The baby and the parent unit have to be checked regularly to ensure they are still working correctly. It is also suggested that reception be checked regularly to ensure the maximum radio range has not been exceeded.
> Empty batteries should be charged as soon as possible and defective batteries should be replaced immediately.
> Do not touch leaking batteries with bare hands, please use protective gloves. The affected areas in and around the unit should be cleaned as soon as possible with a dry cloth. Wash your hands when finished.
> Batteries can be disposed of in the local municipal waste centre. Please check your local waste disposal regulations.
BABY UNIT
1. Power-/Connection indicator (green LED)
LED lit: Power is on and properly connected to the parent unit
LED flashes: No connection with the parent unit
LED off: Power is off
2. ON / OFF button
Press and hold for 2 seconds to turn the device on or off
3. Paging button
Press and hold button until the parent unit beeps. (Help to find a misplaced unit)
4. 6V DC power supply connection
To connect the power supply TEN PAO S003IV0600050
5. Built-in microphone
Detects baby sounds in the radio area of baby unit.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Ansmann Sydney at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Ansmann Sydney in the language / languages: All languages as an attachment in your email.
The manual is 4,4 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
