792117
12
Zoom out
Zoom in
Previous page
1/16
Next page
6. 5 SPECTRUM CHART
This menu shows the spectrum chart of the setting frequency range. Please see below screenshot.
Press
▼/▲
to switch between current frequency, start frequency and end frequency:
Press
/
to change start or end frequency of the spectrum frequency range if the curse is focusing on the
start or end frequency icon.
User`s Manual
17 / 25
6.2
A
UTO
S
CAN
The meter will scan all the saved frequencies and show the
lock status one by one and will then return to the main
menu once scanning is finished. Press [MENU] to abort a
scan in progress and return to the main menu.
6.3
RF
C
HANNEL
L
IST
This menu shows all the locked frequencies during Auto Scan.
6.4
S
COPE
This screen show 6 channels level (dBuV) in one page, use
[/] to move focus on channel number and press [OK]
change channel number.
6.
5
S
PECTRUM
C
HART
This menu shows the spectrum chart of the setting
frequency range. Please see below screenshot.
Press [/] to switch between current frequency, start
frequency and end frequency:
Press [/] to change start or end frequency of the
spectrum frequency range if the curse is focusing on the
start or end frequency icon.
40~50~60: The range of the level value. Press [F3] to switch range between 40~60,
40~80 and 40~100.
C6/175MHz/0 dBuV: The curse of the current frequency and power level. Press [/]
to change the value.
162: The start frequency of the spectrum chart.
498: The end frequency of the spectrum chart.
5V: Show the antenna power output 5V status. The 5v output is on if the
icon is green.
12V: Show the antenna power output 12V status. The 12v output is on if the
icon is green.
18V: Show the antenna power output 18V status. The 18v output is on if the
icon is green.
6.6
ANT
P
OWER
User can enable/disable the power supply for antenna. 5v, 12v and 18v output are supported.
40~50~60:
The range of the level value. Press [F3] to switch range between 40~60, 40~80 and 40~100.
C6/175MHz/0 dBuV: The curse of the current frequency and power level. Press
/
to change the value.
162: The start frequency of the spectrum chart.
498: The end frequency of the spectrum chart.
5V: Show the antenna power output 5V status. The 5v output is on if the icon is green.
12V: Show the antenna power output 12V status. The 12v output is on if the icon is green.
18V: Show the antenna power output 18V status. The 18v output is on if the icon is green.
6.6 ANT POWER
User can enable/disable the power supply for antenna. 5v, 12v and 18v output are supported.
7. DVBC
User can measure DVB-C live signal in this submenu. There are total six submenus: Cable Measure, Auto scan, RF
channel list, Tilt , Spectrum chart and Trunk voltage.
User`s Manual
18 / 25
7.
DVB-C
User can measure DVB-C live signal in this submenu. There
are total six submenus: Cable Measure, Auto scan, RF
channel list, Tilt , Spectrum chart and Trunk voltage.
7.1
C
ABLE MEASURE
User can read SNR, BER, PER, level, strength and quality of
the live signal.
: The lock status. The signal is locking if the icon is green otherwise the
color of the icon is red.
C18: The frequency channel name.
DVB C: The cable system. The values are DVB C ,DVB C2 and MCNS. Press [/]
to switch them.
FREQ: The current frequency. Press [/] to change the value or press [OK] to
edit it.
SYM: The symbol rate of the current signal. The device will get it
automatically once the signal is locking.
SNR: The signal noise rate value of the live signal.
BER: The bit error rate of the live signal.
PER: The packet error rate of the live signal.
LEVEL: The power level value of the live signal.
Str: The strength value of the connected signal.
Q l t : The quality value of the connected signal.
7.2
A
UTO
S
CAN
The meter will scan all the saved frequencies and show the
lock status one by one and will then return to the main
menu once scanning is finished. Press [MENU] to abort a
scan in progress and return to the main menu.
7.3
RF
C
HANNEL
L
IST
This menu shows all the locked frequencies during Auto Scan.
7.1 CABLE MEASURE
User can read SNR, BER, PER, level, strength and quality of the live signal.
User`s Manual
18 / 25
7.
DVB-C
User can measure DVB-C live signal in this submenu. There
are total six submenus: Cable Measure, Auto scan, RF
channel list, Tilt , Spectrum chart and Trunk voltage.
7.1
C
ABLE MEASURE
User can read SNR, BER, PER, level, strength and quality of
the live signal.
: The lock status. The signal is locking if the icon is green otherwise the
color of the icon is red.
C18: The frequency channel name.
DVB C: The cable system. The values are DVB C ,DVB C2 and MCNS. Press [/]
to switch them.
FREQ: The current frequency. Press [/] to change the value or press [OK] to
edit it.
SYM: The symbol rate of the current signal. The device will get it
automatically once the signal is locking.
SNR: The signal noise rate value of the live signal.
BER: The bit error rate of the live signal.
PER: The packet error rate of the live signal.
LEVEL: The power level value of the live signal.
Str: The strength value of the connected signal.
Q l t : The quality value of the connected signal.
7.2
A
UTO
S
CAN
The meter will scan all the saved frequencies and show the
lock status one by one and will then return to the main
menu once scanning is finished. Press [MENU] to abort a
scan in progress and return to the main menu.
7.3
RF
C
HANNEL
L
IST
This menu shows all the locked frequencies during Auto Scan.
User`s Manual
16 / 25
6.
DVBT/T2/ISDBT
User can measure the live DVB-T/T2 signal, analyze the
spectrum, the scope between transponders , auto scan all
the saved frequencies and list all the locked ones. There
are six submenus: Measure, Auto Scan, RF Channel List ,
Scope, Spectrum chart and ANT power.
6.
1
T
ERRESTRIAL
M
EASURE
The device will show SNR, CBER, VBER, power value,
strength and quality of the connected live signal. Please see
below for detail.
: The lock status. The signal is locking if the icon is green otherwise the
color of the icon is red.
C12: The channel name.
5V, 12V,18V: The antenna output voltage. The color of icon will be green once the voltage
is outputting or the color is gray.
DVB T2: The terrestrial system. The values are DVB T and DVB T2. Press [/]
to switch them.
FREQ: The current frequency. Press [/] to change the frequency or [OK]
to edit it.
BW: The bandwidth of the live signal. Press [/] to switch between 6M,
7M and 8M.
SNR: The signal noise rate value of the live signal.
CBER: The CBER(BER before FEC) value of the live signal.
LBER: The LBER(BER after LDPC) value of the live signal.
LEVEL: The power level value of the live signal.
Str: The strength of the live signal in percent.
Qlt: The quality of the live signal in percent.
: The lock status. The signal is locking if the icon is green otherwise the color of the icon is red.
C18: The frequency channel name.
DVB C: The cable system. The values are DVB C ,DVB C2 and MCNS. Press
/
to switch them.
FREQ: The current frequency. Press
/
to change the value or press [OK] to edit it.
SYM: The symbol rate of the current signal. The device will get it automatically once the signal is locking.
SNR: The signal noise rate value of the live signal.
BER: The bit error rate of the live signal.
PER: The packet error rate of the live signal.
LEVEL: The power level value of the live signal.
12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amiko TSC-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amiko TSC-1000 in the language / languages: English as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info