792117
10
Zoom out
Zoom in
Previous page
1/16
Next page
User`s Manual
14 / 25
User need to adjust the attitude of the meter according BLUE arraw on the screen. The meter will
deep and the RED icon turns to GREEN if the RED icon closes to the YELLOW one. It is better to make
the two icon overlapping. And also values of azimuth and elevation will refresh on time according to
the current position during the whole process.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
5.6
D
I
SE
Q
C
M
ONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input
port . Then the meter analyzes all input commands for DiSEqC or switch on this menu, and
also shows the power supply and 22K status. The menu displays the last two commands.
Please refer to below screenshot.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
User`s Manual
14 / 25
User need to adjust the attitude of the meter according BLUE arraw on the screen. The meter will
deep and the RED icon turns to GREEN if the RED icon closes to the YELLOW one. It is better to make
the two icon overlapping. And also values of azimuth and elevation will refresh on time according to
the current position during the whole process.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
5.6
D
I
SE
Q
C
M
ONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input
port . Then the meter analyzes all input commands for DiSEqC or switch on this menu, and
also shows the power supply and 22K status. The menu displays the last two commands.
Please refer to below screenshot.
5.6 DISEQC MONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input port . Then the meter
analyzes all input commands for DiSEqC or switch on this menu, and also shows the power supply and 22K
status. The menu displays the last two commands. Please refer to below screenshot.
User`s Manual
15 / 25
Pow: The power supply of the input cable line.
22KHz: The 22k status of the input cable line.
E03F20D1: The command data of the input cable line. The pre-command.
Move centre: The behavior of dish for command E03F20D1.
E13F21D6: The command data of the input cable line. The current command.
Move west one step: The behavior of dish for command E13F21D6.
DiSEqC1.2/USALS: The command protocol type.
Pow: The power supply of the input cable line.
22KHz: The 22k status of the input cable line.
E03F20D1: The command data of the input cable line. The pre-command.
Move centre: The behavior of dish for command E03F20D1.
E13F21D6: The command data of the input cable line. The current command.
Move west one step: The behavior of dish for command E13F21D6.
DiSEqC1.2/USALS: The command protocol type.
6. DVBT/T2/ISDBT
User`s Manual
16 / 25
6.
DVBT/T2/ISDBT
User can measure the live DVB-T/T2 signal, analyze the
spectrum, the scope between transponders , auto scan all
the saved frequencies and list all the locked ones. There
are six submenus: Measure, Auto Scan, RF Channel List ,
Scope, Spectrum chart and ANT power.
6.
1
T
ERRESTRIAL
M
EASURE
The device will show SNR, CBER, VBER, power value,
strength and quality of the connected live signal. Please see
below for detail.
: The lock status. The signal is locking if the icon is green otherwise the
color of the icon is red.
C12: The channel name.
5V, 12V,18V: The antenna output voltage. The color of icon will be green once the voltage
is outputting or the color is gray.
DVB T2: The terrestrial system. The values are DVB T and DVB T2. Press [/]
to switch them.
FREQ: The current frequency. Press [/] to change the frequency or [OK]
to edit it.
BW: The bandwidth of the live signal. Press [/] to switch between 6M,
7M and 8M.
SNR: The signal noise rate value of the live signal.
CBER: The CBER(BER before FEC) value of the live signal.
LBER: The LBER(BER after LDPC) value of the live signal.
LEVEL: The power level value of the live signal.
Str: The strength of the live signal in percent.
Qlt: The quality of the live signal in percent.
10
User need to adjust the attitude of the meter according BLUE arraw on
the screen. The meter will deep and the RED icon turns to GREEN if the
RED icon closes to the YELLOW one. It is better to make the two icon
overlapping. And also values of azimuth and elevation will refresh on
time according to the current position during the whole process.
User can measure the live DVB-T/T2 signal, analyze the spectrum, the
scope between transponders , auto scan all the saved frequencies and
list all the locked ones. There are six submenus: Measure, Auto Scan, RF
Channel List , Scope, Spectrum chart and ANT power.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amiko TSC-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amiko TSC-1000 in the language / languages: English as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info