792117
7
Zoom out
Zoom in
Previous page
1/16
Next page
User`s Manual
10 / 25
5.2.1 USALS Setting:
Press [OK] to enter USALS SETUP menu on Position Type if
the type sets to USALS parameters
019.2°E Astra 19E: The current satellite. Press
[/] to switch between satellites and press
[OK] to enter satellite list to select satellite. Press [OK] button to select the focused satellite
and press [MENU] to exit from edit menu. All the other parameters on the menu will be
refreshed according to the selected satellite.
Customized: Select longitude and latitude by position name. Press [OK] to list all the
positions. Please select Customized if you want to set the longitude and the latitude
manually.
041.0°E / 02.8°N: Show the selected longitude and latitude. And you can edit the value if
Customized is selected.
Move to center: Press [OK] to move the dish to central position.
Move to position: Press [OK] to confirm to move to setting position
5.2.2 Diseqc 1.2 Setting:
Press [OK] to enter Diseqc 1.2 setting menu on Position
Type if the type sets to Diseqc 1.2
Move single step: Move the motor by step. Press [/] to move to west or east
Move incessantly: Move the motor incessantly. Press [/] to move to west or
east
Move to centre: Press [OK] to move to centre point
Limit east: Set the move limit to east
Limit west: Set the move limit to west
Save and Commit: Press [OK] to save current position
Str.: The strength of signal
Qlt.: The quality of signal
Customized: Select longitude and latitude by position name. Press [OK] to list all the positions. Please select
Customized if you want to set the longitude and the latitude manually.
0
41.0°E / 02.8°N:
Show the selected longitude and latitude. And you can edit the value if Customized is selected.
Move to center: Press [OK] to move the dish to central position.
Move to position: Press [OK] to confirm to move to setting position
5.2.2 Diseqc 1.2 Setting
Press [OK] to enter Diseqc 1.2 setting menu on Position Type if the type sets to Diseqc 1.2
User`s Manual
10 / 25
5.2.1 USALS Setting:
Press [OK] to enter USALS SETUP menu on Position Type if
the type sets to USALS parameters
019.2°E Astra 19E: The current satellite. Press
[/] to switch between satellites and press
[OK] to enter satellite list to select satellite. Press [OK] button to select the focused satellite
and press [MENU] to exit from edit menu. All the other parameters on the menu will be
refreshed according to the selected satellite.
Customized: Select longitude and latitude by position name. Press [OK] to list all the
positions. Please select Customized if you want to set the longitude and the latitude
manually.
041.0°E / 02.8°N: Show the selected longitude and latitude. And you can edit the value if
Customized is selected.
Move to center: Press [OK] to move the dish to central position.
Move to position: Press [OK] to confirm to move to setting position
5.2.2 Diseqc 1.2 Setting:
Press [OK] to enter Diseqc 1.2 setting menu on Position
Type if the type sets to Diseqc 1.2
Move single step: Move the motor by step. Press [/] to move to west or east
Move incessantly: Move the motor incessantly. Press [/] to move to west or
east
Move to centre: Press [OK] to move to centre point
Limit east: Set the move limit to east
Limit west: Set the move limit to west
Save and Commit: Press [OK] to save current position
Str.: The strength of signal
Qlt.: The quality of signal
Move single step: Move the motor by step. Press
/
to move to west or east
Move incessantly: Move the motor incessantly. Press
/
to move to west or east
Move to centre: Press [OK] to move to centre point
Limit east: Set the move limit to east
Limit west: Set the move limit to west
Save and Commit: Press [OK] to save current position
Str.: The strength of signal
Qlt.: The quality of signal
5.3 EDIT SATELLITE
The parameters of satellite, such as Orbit Position and Transponder can be edit in this menu. All the satellites
will be listed in this menu.
User`s Manual
11 / 25
5.3
E
DIT
S
ATELLITE
The parameters of satellite, such as Orbit Position and
Transponder can be edit in this menu. All the satellites will
be listed in this menu.
Press [/] buttons to move curse in list.
Press [F2] button to edit the name or the orbit position of
current satellite in the dialog. And then press [/] to
move curse and [/] to change value of each focused
item in edit menu.
Press [F3] to add new satellite. Press [F4] to enter delete
satellite dialog, and then press [OK] to confirm to delete or
press [MENU] to cancel.
Press [OK] to enter transponder list of current satellite.
On transponder list menu, press [OK] or [F2] to edit
transponder. Press [F3] to add new transponder. Press [F4]
to enter delete dialog, press [OK] to confirm to delete or
press [MENU] to cancel. And press [OK] button to edit
selected transponder. And then press [/] to move
curse and [/] to change value of each focused item in edit menu.
5.4.
S
PECTRUM
C
HART
This menu will show the spectrum chart of setting
frequency range on current cable line. Press [/] to
switch curser focus between Start Frequency, End
Frequency, LNB Setting and Current Frequency Mark.
22K: Show the RF 22k status. The 22K
is on if the icon is green.
13V: Show the RF power output 13V status. The 13v output is on if the icon is
green.
18V: Show the RF power output 18V status. The 18v output is on if the icon is
green.
Press
▼/▲
buttons to move curse in list.
Press [F2] button to edit the name or the orbit position of current satellite in the dialog. And then press
/
to move curse and
▼/▲
to change value of each focused item in edit menu.
User`s Manual
11 / 25
5.3
E
DIT
S
ATELLITE
The parameters of satellite, such as Orbit Position and
Transponder can be edit in this menu. All the satellites will
be listed in this menu.
Press [/] buttons to move curse in list.
Press [F2] button to edit the name or the orbit position of
current satellite in the dialog. And then press [/] to
move curse and [/] to change value of each focused
item in edit menu.
Press [F3] to add new satellite. Press [F4] to enter delete
satellite dialog, and then press [OK] to confirm to delete or
press [MENU] to cancel.
Press [OK] to enter transponder list of current satellite.
On transponder list menu, press [OK] or [F2] to edit
transponder. Press [F3] to add new transponder. Press [F4]
to enter delete dialog, press [OK] to confirm to delete or
press [MENU] to cancel. And press [OK] button to edit
selected transponder. And then press [/] to move
curse and [/] to change value of each focused item in edit menu.
5.4.
S
PECTRUM
C
HART
This menu will show the spectrum chart of setting
frequency range on current cable line. Press [/] to
switch curser focus between Start Frequency, End
Frequency, LNB Setting and Current Frequency Mark.
22K: Show the RF 22k status. The 22K
is on if the icon is green.
13V: Show the RF power output 13V status. The 13v output is on if the icon is
green.
18V: Show the RF power output 18V status. The 18v output is on if the icon is
green.
7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amiko TSC-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amiko TSC-1000 in the language / languages: English as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info