661060
7
Zoom out
Zoom in
Previous page
1/16
Next page
ALPINE MRV-M1200 68-29530Z91-A (EN/FR/ES)
5-EN
EN
FR
ES
Speaker Output Terminals
The speaker terminals of this unit are insert
terminal type.
Be sure to observe correct speaker output
connections and polarity in relation to the other
speakers in the system. Connect the positive
output to the positive speaker terminal and the
negative to negative.
About Bridged Connections
In the bridged mode, connect the left positive to
the positive terminal of the speaker and the
right negative to the negative terminal of the
speaker. Do not use the speaker (–) terminals as
a common lead between the left and right
channels.
NOTES:
Do not connect the speaker (–) terminal to the
vehicles chassis.
The input is stereo but the output is monaural.
Reversing subwoofer polarity (swapping
positive and negative connections to the
subwoofer) may be desirable in some
installations for optimum bass performance.
Fuse: 25A x 4
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do so may result in fire or electric
shock.
Power Supply Terminal
Battery Lead (Sold Separately)
Be sure to add an in-line fuse with the battery
lead as close as possible to the batterys positive
(+) terminal. This fuse will protect your vehicles
electrical system in case of a short circuit. See
below for appropriate fuse value and minimum
wire gauge requirement:
100 amp fuse, 4 AWG/21 mm
2
Ground Lead (Sold Separately)
Connect this lead securely to a clean, bare metal
spot on the vehicles chassis. Verify this point to
be a true ground by checking for continuity
between that point and the negative (–)
terminal of the vehicles battery. Ground all your
audio components to the same point on the
chassis to prevent ground loops while keeping
wire length as short as possible.
Minimum required wire gauge for this
connection is as follows:
4 AWG/21 mm
2
Remote Turn-On Lead (Sold Separately)
Connect this lead to the remote turn-on
(positive trigger, (+) 12 V only) lead of your head
unit. If a remote turn-on lead is not available, see
“CONNECTION CHECK LIST section on
page 8 for alternative method.
NOTE:
When connecting the speaker output leads of
the head unit to this unit with a Speaker Input
Connector (included), you do not need to
connect the remote turn-on lead, owing to the
“REMOTE SENSING” function of this unit.
However, the “REMOTE SENSING” function may
not work depending on the signal source
connected. In such a case, connect the remote
turn-on lead to an incoming power supply
cord (accessory power) in the ACC position.
Speaker Level Input Connector
These input leads are for use with head units not
equipped with preamp outputs. When not using
the RCA Line Input connectors, you should
connect these wires to the speaker output leads
of your head unit. The MRV-M1200 accepts input
from high power or standard power head units.
NOTE:
For the “Speaker Level Input System setting,
connecting the Remote Turn-On Lead is not
required due to the “REMOTE SENSING”
function of this product. However, the
“REMOTE SENSING” function may not work
depending on the signal source connected. In
such a case, connect the Remote Turn-On Lead
to an incoming power supply cord (accessory
power) in the ACC position.
onnect
ur
essors,
e
ler for
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine MRV-M1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine MRV-M1200 in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info