541352
47
Zoom out
Zoom in
Previous page
1/52
Next page
Qu-16 User Guide 47 AP9031 iss.3
11.Resetting the Mixer
There are two ways to reset the Qu settings:
11.1 Reset Mix Settings – A starting point for mixing
This button in the Scenes screen resets the mixer to a
known starting point for mixing. It provides a quick way
to reset the processing, mixes and patching before a
show or after another user has finished with it.
All parameters that can be stored in Scene memories
are reset to a factory default. Parameters that are not
stored in scenes are not affected. This reset does not
affect existing scenes stored in the mixer.
If you want to keep your current settings then save
these as a Scene before resetting the mixer.
Touch and hold the Reset Mix Settings button for 1
second until the confirmation screen appears. The
hold function prevents accidental operation during
performance. Touch Yes to reset the mixer or No to
exit without resetting.
This ‘resets the board’ ready for mixing:
All preamps are patched and have nominal mic
gain set and phantom power switched off, a good
start for vocal microphones,
All EQ is switched in and set flat ready to start
adjusting tone,
Gates and compressors are switched out but have
their parameters set ready for being switched in
for applications such as drum gating and vocal
compression,
Channels are assigned to the mixes and FX with
their faders and send levels turned down ready to
start dialling into the mix,
The mixes are set pre-fade and sourced post-EQ,
pre-compressor ready to be used as monitor
sends, a common application for the mixes.
The FX master and return faders are turned up
and a default reverb and delay patched ready for
you to hear the effects as soon as you raise a
channel send.
The Mix master faders are turned up ready to hear
sound when you raise a channel send. The main
LR master is turned down to avoid unexpected
loud level in the PA.
The output patching follows the main LR mix to
suit the more common applications.
Creating your own start settings – You
can start by resetting the mixer and then editing the
patching, levels and parameters to suit your starting
preferences. Name and store this as a Scene, for
example Scene 1 “Reset Board”. You could also copy
this to another Scene as a backup.
Reset mix settings:
Source Preamp, Gain 28dB, 48V off
ST1-3 trim 0dB
HPF out, 100Hz
PEQ and GEQ in, flat
Gates out, thres -36dB, depth 20dB
Comp out, thres 0dB, ratio 3.2:1
Delays 0ms
Mix source post-EQ
Sends to Mixes -Inf and pre-fade
Sends to FX -Inf and post-fade
Direct Out post-fade/mute, trim 0dB
Mutes off
Channel faders -Inf
FX return faders 0dB
FX send and Mix master faders -4dB
LR master fader -Inf
FX1 = Mix>Return, Reverb (EMT250)
FX2 = Mix>Return, Delay (Vocal)
FX 3 and 4 = unassigned
Mute Groups unassigned
AES, Alt Out patch LR post-fade
Qu-Drive stereo patch LR post-fade
USB patch CH1-16, ST1-3, LR
Talkback unassigned, HPF 120Hz
Custom Strip unassigned
SoftKeys = Mute Groups 1-4
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath QU-16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath QU-16 in the language / languages: English as an attachment in your email.

The manual is 7,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info