541363
17
Zoom out
Zoom in
Previous page
1/48
Next page
ML3000 User Guide 17
MATRIX 1-4 EXT INPUT 0dBu line level balanced
TRS jacks to connect external signals into the
matrix. Each matrix has its own input. There are
no level trims for these inputs.
LOCAL MONITOR OUT Impedance balanced
stereo monitor output on TRS jacks. These can
connect to a stereo amplifier/speaker system for
local monitoring.
2-TRACK IN / OUT Line level TRS jacks to
connect to a 2-track recorder such as MiniDisc, tape
or DAT. Connect OUT to the recorder input, and IN
to the recorder output. The connections are
balanced. Link ring (cold) to sleeve (ground) when
connecting to unbalanced equipment.
TB/OSC OUT Impedance balanced TRS line level
output providing talkback, 1kHz oscillator or pink
noise when selected. Use this to patch the test
signal into console channels or other equipment.
MIDI Two standard opto-isolated 5-pin sockets for
MIDI IN and OUT. The small slide switch selects
either the MIDI or RS232 connection. For normal
console operation it is recommended that the switch
is set to MIDI. The power up boot routine is quicker
in this position than RS232.
RS232 9-pin D-connector to connect to the serial
port of a PC for loading new console operating
software, archiving the settings or controlling the
snapshot memories. To enable RS232 set the slide
switch to the RS232 position. Set it to the MIDI
position when RS232 is not needed.
LAMP 4-pin XLR for plugging in a gooseneck lamp
to illuminate the control surface. Three lamp
sockets are provided along the back of the
meterpod. The right angled Littlite type is
recommended. The 4-pin XLR prevents any
confusion with the 3-pin audio connections.
SYS-LINK EXPANDER OPTION The console is
provided with blanking plates fitted as standard.
The ML3000 Sys-Link option kit is available from
Allen & Heath. It is fitted by removing the base,
blanking plates, and plugging in the circuit cards
provided. Fitting instructions come with the kit.
Two pairs of 37-pin and a pair of 9-pin D-connector
sockets allow two consoles to connect together as
master and slave to expand the number of channels
in the mix. These provide access to all the mix
busses and P/AFL system. They are balanced and
operate at –2dBu line level.
Two ML3000 consoles may be linked as
master/slave. Alternatively the ML3000 may be
connected as a slave to an ML4000 or ML5000
console.
Two 37-way audio and one 9-way logic cables are
required. The audio outputs of the slave console
plug into the master audio inputs. The slave
console SLAVE logic connector plugs into the
master console MASTER logic connector.
The Sys-Link connections conform to the Allen &
Heath Sys-Link II standard. You can connect to a
console fitted with Sys-Link I using special adapter
cables. Contact Allen & Heath for details.
Refer to the Sys-Link fitting instructions for further
details on this option.
DIRECT OUT
OUTPUT
( to master )
SLAVE
SYS-LINK LOGIC
( from slave )
MASTER
INSERT
INPUT
INSERT
INPUT
INSERT
INPUT
DIRECT OUT
P
UTS
DIRECT OUT DIRECT OUT
INSERT
INPUT
BA
AUDIO OUTPUT ( to master )
OUTPUT
SYS-LINK ( option )
INSERT
INPUT
INSERT
INPUT
INSERT
INPUT
INSERT
INPUT
DIRECT OUTDIRECT OUT DIRECT OUT DIRECT OUT
AUDIO INPUT ( from slave )
SYS-LINK ( option )
INSERT
DIRECT OUT
INPUT
INPUT A
INSERT
DIRECT OUT
INPUT
INSERT
INPUT
DIRECT OUT
INSERT
INPUT
DIRECT OUT
INSERT
INPUT
DIRECT OUT
INSERT
INPUT
DIRECT OUT
INPUT B
INPUT
INSERT
DIRECT OUT
INSERT
INPUT
DIRECT OUT
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath ML 3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath ML 3000 in the language / languages: English as an attachment in your email.

The manual is 3,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info