541378

Allen-Heath MixWizard Series WZ20S Manual

23
Zoom out
Zoom in
Previous page
1/32
Next page
WZ20S User Guide 23
AUXILIARY MASTERS These provide six independent mix
outputs which can be used to provide foldback, cleanfeed and cue
monitors, effects and recording sends, zone feeds and any other
special mixes required.
AUX 1-6 Adjust the output level of each auxiliary mix. Turning the
control clockwise adjusts from fully off to +4dB boost. The normal ‘0’
position is marked.
MIX1 AND MIX2 MASTERS These are the main console
outputs. You can route each input channel to either or both outputs.
You can route MIX to create a stereo subgroup to MIX2 main output.
Both outputs provide master fader control, inserts, metering and
balanced XLR outputs. MIX2 provides additional TRS jacks and an
XLR mono output. This provides the flexibility to satisfy most audio
system applications. Refer to the section on applications later in this
User Guide.
MIX1 METERS A pair of meter bars display the post-fader left and
right output levels of stereo MIX1. Each meter has 12 LEDs to
indicate signal levels from as low as –30dB. Green and yellow LEDs
indicate normal operating levels. The top red LED lights at +16dB to
warn that you are within 5dB of clipping. Meter ‘0’ represents +4dBu at
the main outputs. The meters are peak responding. This means that
they have a fast attack and are able to display fast transients
accurately. With the output faders at their ‘0’ mark you should adjust
the mix so that the signal averages ‘0’ on the meters with highest
peaks no more than ‘+6’. This still leaves plenty of mix headroom.
MONITOR / MIX2 METERS A pair of meter bars displays the level of
the selected monitor source or PFL. With all selector switches up
these default to display the post-fader left and right output levels of
stereo MIX2.
MIX1 to MIX2 Routes the post-fader MIX1 signal to MIX2 to create a
stereo subgroup. Route all the channels you want to group to MIX1
only. Route the other channels to MIX2 only. Press the underpanel
MIX2 switch above the master fader to route MIX1 to MIX2. This is a
tamperproof switch to avoid accidental operation in situations where
MIX1 and 2 are used as independent outputs. It should be selected
using a pen or similar pointed object. MIX1 becomes a subgroup
giving you single fader control over all routed levels. You can also
insert a signal processor such as a compressor to affect all signals in
the group. MIX2 becomes the main output.
MASTER FADERS MIX1 and MIX2 each have a 100mm long throw
fader to adjust the output level. This is a stereo fader which adjusts
the left and right signals at the same time. The ‘0’ mark indicates
normal operating position. The fader can be set above or below this
depending on the output level required. A further 10dB of boost is
available at the top of its travel. However, if you find yourself normally
setting the fader in the lower half of its travel then the connected
equipment may be too sensitive for the operating level of the console.
With the fader set to its ‘0’ position adjust the input level trim of the
connected equipment accordingly.
The MIX1 and MIX2 insert points are pre-fader. The level of any
inserted processing equipment will be affected by the master faders.
The inserted equipment should be set to match the –2dBu operating
level of the console.
MIX2MIX1
OO OO
20
30 30
20
0 0
5
10 10
5
10
5 5
10
010
EXT1
DIM
6
1
EXT2
MIX1
PFL
5
0
MIX2
MONO
1
3
4
2
OO
O
AUX
6
O
+4
SPLIT
PFL ENABLE
+4
0
MONITOR
9
7
8
LOCAL
ALL UP =
MIX2
AUX1
AUX3
AUX2
AUX5
AUX4
AUX6
O
AUX
5
O
O
4
AUX
O
+4
5-6
6
+4
4
5
O
AUX
3
O
O
AUX
O
2
2
+4
3
3-4
+4
0
1-2
1
-3-3
MONITOR
6
R
AUX
1
5
0
4
2
1
3
MIX1
RL
PFL
L
-12-12
-30
-20
-16
-20
-30
-16
-6
-9 -9
-6
LEV
8
9
7
PRG
MIX2
0
+3
+6
+3
0
+6
+16
+9
PFL
+9
+16
OO
IN
EXT1
0
+6 OO
MIX2
IN
EXT2
SPLIT PFL
0
+6
POWER ON
MIX1
0
0
0
0
1
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath MixWizard Series WZ20S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath MixWizard Series WZ20S in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info