541368
20
Zoom out
Zoom in
Previous page
1/44
Next page
Allen & Heath 20 GS_R24 User Guide
I/P=DAW switch
This swaps the source for the valve stage from the Mic/Line/Inst
sockets to the interface return for that channel (channels 29 & 30 on
the interface). The pre-amp Gain control will not affect the return
level when sourced from the interface, but the Drive control will.
VALVE INPUT CHANNEL
INST
I/P = DAW
POL
+48V
BOOST
60 40-14 6
30
40
50
0
20
GAIN
MIN MAX
Drive
INST
Line/Instrument Input Jack Socket
Standard 1/4” (6.25mm) Jack socket. This is an unbalanced input de-
signed so that it can be used for instruments with either line level
(active) outputs or low level magnetic or piezo pickups.
Wired Tip=Hot(+), Ring=cold (0V), Sleeve=Chassis.
Insert Jack Socket
Standard 1/4” (6.25mm) Jack socket for unbalanced insert send and
return signals. Wired Tip=send, Ring=return, Sleeve=Chassis. Nomi-
nal level is 0dBu. The insert point is after the valve pre-amp stage.
Microphone Input Socket
Standard 3-Pin XLR socket wired as Pin 1=Chassis, Pin 2=hot (+),
Pin 3=Cold (-).
Direct Output Jack Socket
Standard 1/4” (6.25mm) Jack socket for Valve channel output signal.
Wired Tip=Hot(+), Ring=Cold(0V), Sleeve=Chassis. Nominal level is
0dBu. The source for the Direct Output is taken from pre the mas-
ter level control and is impedance balanced which means that the
source resistance to the Tip(+) and Ring(0v) contacts are matched in
order to maintain common-mode interference rejection.
REAR PANEL CONNECTIONS
FRONT PANEL CONTROLS
48V Phantom Power Switch
Applies +48V to pins 2 and 3 of the XLR input though 6k8 resistors
for phantom powered condenser microphones.
Polarity (phase) reverse switch
Reverses the polarity of the balanced input signal phases for both
mic XLR and Line jack inputs.
Line/Instrument Input Switch
Selects the source for the pre-amp from XLR to Line/Instrument
input jack. The jack input is extremely high impedance (10M) and
utilises a class A FET circuit as a front end to the pre-amp. This in
itself emulates a thermionic valve input stage in its tonal quality and
saturation characteristics.
Boost Instrument level switch
Increases the gain of the FET pre-amp by 26dB when pressed. Useful
for low output pickups of when the saturation characteristics of the
pre-amp circuit are utilised.
Important! This switch is liable to cause clicks or
thumps when pressed—turn down your master
level to avoid unwanted clicks.
T
T
INSERT
DIRECT
OUT
MIC
INST
IN
LINE/
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GS-R24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GS-R24 in the language / languages: English as an attachment in your email.

The manual is 8,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info