541368
19
Zoom out
Zoom in
Previous page
1/44
Next page
Allen & Heath 19 GS_R24 User Guide
STEREO INPUT CHANNEL
MUTE
I/P=DAW
SEND=
DAW
SOLO/
SELECT
POST EQ
10
0
10
20
30
40
DAW send source switch
This switch determines the source for the interface send for the stereo chan-
nel. In the up position the source is taken from the post-level input signals. If
the switch is pressed then the source is taken from after the stereo EQ. One
or the other signal will always be sent to the interface.
INTERFACE CONFIGURATION SWITCHES
Stereo input channel source = DAW
The I/P=DAW switch swaps the source for the stereo channel from the Jack
socket/RCA phono connectors to the interface returns for that channel.
Mute Switch
This mutes or cuts the signal to the mix buses, the post-fade Auxes and the
pre-fade Auxes (where muting is enabled). A rectangular LED illuminates to
show the Mute switch is pressed. The “soft” mute circuit has a time constant
of 30mS for minimum Fourier clicks caused by sharp edges, and can be trig-
gered by soloing another channel in Solo in Place mode.
Solo/Select Switch
The channel solo/select switch is multi-functional switch that operates as a
channel solo switch or a MIDI select switch to control DAW parameters,
The modes are set by selector switches in the master section and are as fol-
lows:
1) PFL: Sends a pre-fade (also pre-mute) mono sum of left & right signals
from the stereo channel to the monitoring system.
2) AFL: Sends an after-fade (also post Bal) stereo signal to the monitoring
system.
3) Solo in Place: Any pressed solo switches will mute other mono input
or stereo input channels (unless SiP safed) unless their solo switches
are pressed also (in ADD mode).
4) Select: The channel monitoring is disabled and the switch sends a MIDI
message. The LED illumination can be tallied internally or can be tal-
lied by the DAW in order to maintain synchronisation of status.
Fader
A 100mm stereo fader controls the level of the left & right channel signals to
mix buses and post-fade auxes. The stereo channel faders are not MIDI en-
abled and cannot be motorised or automated.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GS-R24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GS-R24 in the language / languages: English as an attachment in your email.

The manual is 8,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info