693707
26
Zoom out
Zoom in
Previous page
1/62
Next page
Connections
Multimix 12R Reference Manual 15
You don’t need to connect anything to the other input of the effect,
because most effect units use the stereo inputs only to provide a path
for the “dry” stereo signal when the effect is connected directly
between an instrument and an amplifier. In mixing applications such
as with the Multimix 12R, you will set the effect’s wet/dry balance all
the way to “wet” (effects only, no direct signal). The effect device will
generate an artificial stereo output from the signal input. Check the
manual for your effect device for more information.
On the other hand, true dual-channel effects processors (such as the
Alesis QuadraVerb 2) may be connected to two different sends to take
advantage of the dual processing capability. Dual-channel processors
allow the left and right inputs to be used for different kinds of effects
(for example, the left input to a stereo chorus while the right input is
used for a stereo reverb).
Using Aux 1 as an effects send
Note that [AUX 1] may also be used as an extra effects send. Although
Aux 1 is a pre-fader send, and normally used for stage monitoring or a
separate headphone mix while recording, it may also be used as an
effects send so you can add different effects to different channels. Just
remember that the “PRE” under [AUX 1] means that when you move
a fader up or down you won’t change the level going to an effect from
Aux 1. If you change fader levels, you will need to adjust Aux 1 levels
to maintain the same balance between dry and effected signal.
In-line processing using the INSERT jacks
(compressors & equalizers)
Some signal processors are designed to be used on one signal at a
time, with the entire signal being processed instead of a mix of effected
and uneffected signal. The purpose of the INSERT jacks on channels 1-
8 is to allow you to insert a compressor, equalizer, or other effect into
the signal path of a single channel after its preamplifier and [TRIM]
control, but before the Multimix 12R's own EQ, aux sends, and fader.
The INSERT jacks may also be used as direct outputs to a recorder.
The INSERT connector is a TRS (tip/ring/sleeve) 1/4" jack which
consists of an insert send (the tip of the TRS plug) and an insert return
Connections
(the ring of a TRS plug). A special Y-cable consisting of a TRS 1/4" plug
on one end and two mono 1/4" plugs on the other end is required.
Tip
Ring
Sleeve
Send
Return
Ground
Tip
Ring
Sleeve
Insert Points
Note that you will not hear any signal through the Multimix 12R if
the INSERT jack is plugged in and the signal is interrupted in that
loop (by the other cables being disconnected, the processor being
turned off, or the volume turned off in the processor).
Connecting an in-line processor
1. Obtain a "stereo splitter" insert cable from your dealer.
2. Connect the stereo (TRS) end to the INSERT jack of the Multimix
12R.
3. Connect the mono plug from the tip connector to the input of the
processor.
4. Connect the mono plug from the ring connector to the output of
the processor.
If you're not sure which mono plug is from the tip and which is from
the ring, check to see if the cable is labeled. If not, simply try it one
way and if the signal doesn't pass through, swap the input and output
plugs the other way.
The [INSERT] jack may also be used as a direct output to a multitrack
recorder such as the ADAT. The send from the insert jack is where the
cleanest mic preamp signal may be obtained, without passing through the EQ
or channel circuitry. Simply insert the plug to the first "click" (the ring
connector) and it will not interrupt the flow through the mixer, while
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alesis MultiMix 12R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alesis MultiMix 12R in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info