693707
28
Zoom out
Zoom in
Previous page
1/62
Next page
Connections
Multimix 12R Reference Manual 17
providing a direct output. Or, put the recorder into INPUT mode and insert
the plug all the way, connecting the input and output of each track of the
recorder into each channel path of the mixer. This will allow playback
monitoring of the recorder. See the Applications chapter for more
information.
For more information on using the AUX and INSERT systems, see the
“Operating Instructions” chapter of this manual.
Connections
Outputs
To a stereo PA system or instrument
amplifier
Balanced
Check to see if your amplifier can accept balanced inputs. If so,
connect the [MAIN OUT BALANCED] jacks of the Multimix 12R to the
input of the amp using a 3-conductor cable, with a 1/4" TRS plug on
one end, and the connector used by the amp (usually a 1/4" TRS
connector; sometimes an XLR or terminal strip) on the other.
You may also connect the [MONITOR OUT] jacks of the mixer to your
amplifier. This will allow you to switch between hearing 2-track playback
and the stereo output of the mixer, using the front panel monitor switch.
Unbalanced
If the amp is unbalanced, use a standard shielded "patch cord" with
1/4" connectors.
To a mono system
If your PA system or amplifier isn't stereo, connect either the left or
right MAIN OUT jacks to the input of the system. Make sure that all
[PAN] controls are in the center or turned to the side you're using.
To a stage monitor (foldback) system
If your PA system has a separate amplifier and speaker system for
monitors, connect a cable from the [AUX 1 PRE AUX SENDS] jack to
the amp input, in the same manner as above. The Aux 1 system is a
pre-fader, post-EQ send with a balanced/unbalanced output. In most
stage monitor situations, we recommend connecting a third-octave
graphic equalizer such as the Alesis MEQ-230 between the mixer and
the amp to control feedback.
The Aux 1 output may be connected in the same way for a number of
different applications such as:
Headphone cue feed for multitrack recording
Separate broadcast mix from a PA system
Zone feed for a separate region of a PA system
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alesis MultiMix 12R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alesis MultiMix 12R in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info