626270

Alde 3010 Control panel - 213 LCD Manual

20
Zoom out
Zoom in
Previous page
1/104
Next page
20
Fault messages19.
In case an error occurs in the system, the display will show the reasons for it (applies only when the boiler
is at rest)
BATT LO: If the vehicle, boat or building has a battery voltage below 10,5 V, the boiler will stop. The heater is
automatically reset when the voltage comes up to 11V.
FAN: Faulty fan speed. Automatic resetting after 5 minutes.
GAS OUT: Gas finished. Resetting by switching off and restarting the boiler in accordance with item 1.
OHEAT 1: Thermostat (blue cable) released. To reset, disconnect 12V from the boiler and connect again.
OHEAT 2: Overheating protection (red cable) released. To reset, disconnect 12V from the boiler and
connect again.
WINDO: Window open, the boiler stops for gas. Gas operation in the boiler starts when the window is closed.
Electrical operation functions. Check in the instructions for vehicle, boat or building, if this
function has been installed.
SERIAL: There is a connection fault between boiler and panel. Normally, this is a mechanical fault in the
connection between the heater and panel. To re-set, break the main current and then start again.
top
Short circuit in the sensor in the control panel or in the remote sensor.•
The outdoor sensor might have been incorrectly connected.•
bot
Short circuit in outdoor sensor.•
Emergency start20.
Disconnect 12V and the cable to the panel on the heater.•
Connect a cable between 2 and 9 in the contact device (on the heater).•
Connect 12V to the heater.•
Now the heater starts with gas and 1kW. (Regulation of room temperature does not function, constant pump
operation).
Automatic temp. increase
At 02.00 hours (night time) the boiler
starts and works in accordance with
Warm water (item 5) if the clock is
set. The reason for this is to reduce
the risk of legionella.
The function is disconnected in
the factory setting.
Press the button with the arrow 1.
until the Menu symbol flashes.
Press +On.
When OF is displayed, step with 2.
the arrow key until LE is dis-
played. Press +/On and legionel-
la is connected.
Press -/Off to disconnect legionel-3.
la. Then press Store to leave the
legionella function.
Constant pump operation
With this function, selected pump
is in constant operation. The func-
tion is disconnected in the factory
setting. This function limits the hot
water supply, particularly when there
is little need of heat.
Press the button with the arrow 1.
until the Menu symbol flashes.
Press +On.
When OF is displayed, step with 2.
the arrow key until PE is dis-
played. Press +/On and constant
pump operation is connected.
Press -/Off to disconnect con-3.
stant pump operation. Then press
Store to leave the pump operation
function.
blinkar
flashes
blinkar
flashes
blinkar
flashes
blinkar
flashes
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alde 3010 Control panel - 213 LCD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alde 3010 Control panel - 213 LCD in the language / languages: All languages as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info