582879

Al-ko Robolinho 4000 Manual

36
Zoom out
Zoom in
Previous page
1/84
Next page
en
Maintenance
36 Robolinho
©
4000
DANGER!
Danger of injury due to the cutting bla-
des!
During transport, always keep the cutting
blade plate facing away from your body.
Cleaning
DANGER!
Danger of injury due to the cutting bla-
des!
During transport, always keep the cutting
blade plate facing away from your body.
1 Once a week, thoroughly clean the automatic
lawnmower with a hand brush or cloth.
➯
Contamination can impair the function of
the machine if not removed.
2 Once a week, check the cutting blades (2-9)
for damage.
ADVICE
Damage to the electrical/electronic
system by incorrect cleaning!
Do not clean the automatic lawnmower
with a high-pressure cleaner or under
running water. Water penetration can
cause irreparable damage to the switch,
battery, motors and circuit boards.
Checking contacts
1 If the contact surfaces (12-2) on the automa-
tic lawnmower are contaminated, clean them
with a cloth.
ADVICE
Charring on the contact surfaces indica-
tes a poor charging contact.
➯
Bend the springs on the base station
outwards (10-1).
Cleaning the chassis
Check the rollers can move freely
1 Once a week, thoroughly clean the areas
around the rollers (13-1) with a hand brush or
cloth.
2 Check the rollers (13-1) can move and steer
freely.
➯
If the rollers (13-1) do not move freely,
they must be freed up or renewed.
Checking the base station
1 Disconnect the mains plug on the transfor-
mer.
2 Check the contacts (10-1) on the base station
for contamination and clean using a cloth if
necessary.
3 Push the contacts towards the base station
and release.
➯
The contacts must spring back into the
initial position.
ADVICE
If the contacts do not spring back into the
initial position, have them checked by an
AL-KO dealer, technician or service part-
ner, and renewed if necessary.
Checking the base station
Before storage (winter) of the Mähroboters follo-
wing points should be noted:
Fully recharge the battery.
Off Lawn Mower.
Clean Lawn Mower.
Replace damaged cutting blade.
Lawnmower Store in a dry, frost-free room.
REPAIR
Repair work is only allowed to be carried out by
expert workshops or our AL-KO service centres.
Repair work is only permitted using original spare
parts.
Renewing the cutting blades
1 Switch off the automatic lawnmower (3-7).
2 Put down the automatic lawnmower with the
cutting blades pointing upwards.
3 Unscrew the screws (2-11) with a 5.5 mm
spanner.
4 Pull the cutting blades (14-5) out of the blade
seat.
5 Clean the blade seat with a soft brush.
6 Insert new blades and screw tight with the
screws.
➯
As a rule, the clearer blades do not need
to be renewed.
In case of stubborn dirt that cannot be removed
with a brush, the blade plate (13-3) must be rene-
wed because an imbalance can lead to increased
wear and malfunctions.
ADVICE
Damage due to an incorrect repair!
If cutting blades are damaged and bent,
they are not allowed to be straightened.
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko Robolinho 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko Robolinho 4000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info