Manual Al-ko KHS 5200 (page 12 of 106) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

460709

Zoom out

Zoom in

1/106

Log splitter

GB 3

Unpacking/Assembly

Caution!

The log splitter should only be used

when all its component parts have been

completely assembled.

1. Check the package contents (Illus. A/B).

Inform the dealer if deficiencies are detected.

Note:

Tools required for assembly/operation

are depicted in Illus. C. These are not

included in the scope of delivery.

Mounting the transport wheels

1. Fit the axle (Illus. 1-2) from outside through

the wheel and through the tube (Illus. 1-1)

and secure it with the spring plug (Illus. 1-3).

Mounting the feet (KHS 5200)

1. Mount the transportation wheels on both the

front feet; see Section “Mounting the trans-

port wheels.”

Warning!

The transportation wheels are only used

to transport the log splitter. During

splitting operation, the wheels must be

removed from the feet and mounted in

the park position (Illus. B-11).

2. Tilt the log splitter on to one side and mount

the front and rear foot.

3. Fit the foot (Illus. 2-2 and Illus. 4-2) up to the

stop limit inside the tubular frame (Illus. 2-1

and 4-1) and secure it firmly in position with

screws, washers, and locking nuts.

4. Tilt the log splitter onto the opposite side with

the help of a second person, and mount the

other feet and afterwards put it upright.

5. Put the log splitter in vertical position (piston

rod upright) and screw the support foot (illus.

3-1) on the rear feet.

6. Erect the log splitter and mount the cross

members in front (Illus 5-1) with the help of

the threaded rod (Illus. 5-1).

Mains connection

1. Connect the cable to the mains supply.

Operation

Caution!

The log splitter should not be operated if

components (e.g. the protective hoops)

are missing or defective or the connec-

tion cable is damaged.

Prior to every use

1. Conduct a visual inspection of the log split-

ter.

2. The log splitter should not be operated if

components are missing, defective or loose.

3. Visually inspect the connection cable. A

defective connection cable (e.g. with cracks,

cuts, crushing damage or bends in the insu-

lation) should not be used.

4. Visually inspect the hydraulic components for

leaks.

Log splitter start-up

Caution!

The log splitter should only be used by

one person.

1. Position the log splitter horizontally on a

level, firm surface, better with a slight inclina-

tion towards the operating lever (since the

valves are seated here). If inclined towards

the splitting wedge it loses splitting force. Do

not deposit the log splitter on the connection

cable!

2. Lay the connection cable so that it cannot be

damaged by bending, crushing or otherwise.

Warning!

The transportation wheels with model

KHS 5200 are only used to transport the

log splitter. During splitting operation, the

wheels must be removed from the feet

and mounted in the park position.

3. Loosen the venting screw (Illus. 6) by 3-4

turns.

Note:

After splitting, tighten the venting screw

(Illus. 6) again .

4. Depending on the length, lay the log such

that the wooden log is held by the log guide

tubes.

capacité hydraulique ( remplacement du liquide hydraulique ,combien de litres SVP ??? ) Submitted on 9-5-2023 at 14:07
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko KHS 5200 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko KHS 5200 Manual

Product: