Manual Al-ko HW F 1004 (page 11 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish)

601989

Zoom out

Zoom in

1/120

• Make sure that the device is protected from

rain and any direct exposure to water.

When attaching the suction and pressure

hoses, make sure that they do not exert a

tension on the device. We recommend the

use of flexible hoses at the pump inlet (13)

and outlet (3). If you have any questions,

ask your retailer.

When operating the system (automatic

operation), take appropriate measures to

ensure that damage due to flooding can-

not occur if the system should malfunction.

This can be ensured, for instance, by

installing an alarm system or a reserve

pump.

Attaching the suction hose

Choose a hose which is long enough so

that the device will not suck in air and run

dry. The hose should be at least 30cm

under the surface of the liquid to be

pumped while the pump is in operation.

• Attach the suction hose. Make sure to screw

it in tightly, but take care not to damage the

threads.

If the liquid to be pumped is deeper than

4 m, you should use a suction hose which

is larger than 1“ in diameter for the best

performance. We recommend our AL-KO

suction set (14), which consists of a

suction hose, strainer and non-return

valve. The suction set is available at your

local retailer’s.

GB 3 Translation of original user instructions

• When laying the suction hose, make sure

that it is lower than the system.

If the suction hose is laid so that it is higher

than the device, bubbles will be- come

trapped in the line and the pump will suck

air.

Attaching the pressure hose

• Screw the connection nipple (17) with the

round seal ring (18) in the pump outlet (3).

• Screw the angular nipple (15) with the flat

seal (16) on the connection nipple (17) and

rotate the angular nipple in the desired direc-

tion.

• Attach the pressure hose. Make sure to

screw it in tightly, but take care not to dam-

age the threads.

Filling the pump

Before putting your domestic water sys-

tem into operation, you must fill the pump

chamber with water until it overflows to

achieve full suction power. Do not operate

the pump while it is dry because this will

cause serious damage to the pump.

• Remove the filler screw (2).

• Pour water into the opening until the cham-

ber of the pump (12) is full.

• Replace the filler screw (2) and tighten it.

Switching on the system

• Open the pressure line (open valve, sprayer,

tap, etc.).

• Plug the electric cable into the socket. The

pump will automatically begin to run.

• As soon as the flow of water is cleared of air

bubbles trapped in the line, close the pres-

sure line. When the pressure has fallen and

the reservoir is full, the pump will automati-

cally switch off. Your domestic water system

is now ready for operation.

Switching off the system

• Switch the system off by unplugging the

electric cable from the socket.

Maintenance and Cleaning

Before beginning any maintenance or

cleaning work, make sure that the device

has been unplugged and take precautions

to ensure that it cannot be switched on

during work!

Cleaning the system

If you have used your domestic water system to

pump chlorine water (swimming pool water) or

liquids which leave a residue, flush your pump

out with clear water after use.

Cleaning the filter

• Remove the screw plug (12) from the drain-

age opening, empty the filter chamber and

close the drainage opening again

• Unscrew the filter cover (14) with the help of

the filter spanner.

• Remove the filter (22) from the pump head

and clean it under flowing water.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko HW F 1004 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 3,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Al-ko HW F 1004 Manual

Product: