594615
16
Zoom out
Zoom in
Previous page
1/150
Next page
en
Safety instructions
16 GTE 350 / 450 / 550
Damaged or brittle extension cables must not
be used.
Check the condition of your extension
cable each time you start to use the
equipment.
Secure the extension cable in the cable strain
relief.
Do not get the appliance wet or expose it to
moisture.
Keep children away from appliances connec-
ted to the mains.
ASSEMBLY
CAUTION!
The machine must not be put in opera-
tion before it has been assembled com-
pletely.
Install the guard plate
ADVICE
The knife integrated in the guard plate
automatically cuts the line to the opti-
mum length.
GTE 350
1. Set the guard plate in relation to the cutter
head (2-1).
2. Make sure that the line is exposed.
3. Secure with the enclosed 4 screws.
GTE 450, GTE 550
1. Set the guard plate in relation to the cutter
head (2-1).
2. Make sure that the line is exposed.
3. Screw the guard plate on at the rear with the
supplied screws (2-1).
4. Place the guide wheel on the guard hood and
tighten the screws (2.2).
Installation of auxiliary handle
GTE 350
1. Pull the grip bar of the auxiliary handle slightly
apart (3-1).
2. Push the auxiliary handle onto the holder
(3-2).
3. Engage the auxiliary handle in the splines.
4. Put on the pin holder and screw the clamping
pin tight (3-3).
GTE 450, GTE 550
The angle of the handle can be individually adjus-
ted using the tip lever.
1. Push the holder onto the shaft.
2. Pull the grip bar of the auxiliary handle slightly
apart (3-1).
3. Push the auxiliary handle onto the holder
(3-2).
4. Engage the auxiliary handle in the splines.
5. Place the tip lever with pin holder onto the
clamping pin.
6. Screw the clamping pin tight so that the tip
lever can be operated with little force (3-3).
STARTUP
CAUTION!
Always perform a visual check prior to
start-up.
Adjusting the telescopic handle
1. To release, turn the upper locking sleeve
through about 180° to the right (4-1).
2. Set the telescopic handle to the individual
physique. The telescopic handle can be ex-
tended by approx. 10 cm (4-2).
3. Tighten the locking sleeve (4-3).
Swivelling the cutter head
To trim lawn edges, for example, it is possible to
swivel the cutter head through 180° (5, 6).
1. Loosen the lower locking sleeve (5-1).
2. Turn the telescopic handle through 180° (5-2).
3. Screw the locking sleeve tight (5-3, 6-1).
Angling the cutter head
By changing the pivot angle, it is also possible to
trim areas that are difficult to access, e.g. under
benches, overhangs, etc.
1. Press the locking button (7-1).
2. Engage the cutter head in the required angle
(7-2).
3. Release the locking button.
ADVICE
Remove the guard on the line cutter be-
fore taking into operation for the first
time.
Starting the lawn trimmer
1. Guide the extension cable through the strain
relief.
2. Connect the extension cable to the mains
supply.
3. Stand securely.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko GTE 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko GTE 450 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info