601591
17
Zoom out
Zoom in
Previous page
1/188
Next page
Assembly
440565_b 17
ASSEMBLY
CAUTION!
Danger of injury if the machine is incom-
plete!
Incomplete machines can lead to injuries
and damage to the machine!
Do not operate the machine unless it has
been fully assembled.
Scope of supply
Carefully remove the shredder from its packaging
and check the following parts for completeness:
Base with grass catcher
Two transport wheels with wheel caps
Upper shredder part with cutting and motor
unit
Hopper
Assembly bag with screws and tools, instruc-
tions for use with warranty card and service
station listing.
Mounting the transport wheels
1. Slide the wheel axle (2/1) into the base (2/2).
2. Next, slide a large 10x20x1.5 washer (2/3)
and the bushing (2/4) onto axle (2/1).
3. Afterwards, slide the transport wheel (2/5)
onto the bushing (2/4).
4. Slide the medium 8x20x1.5 washer (2/6) onto
the thread and secure the transport used a M8
nut (2/7).
5. Finally, press the wheel cap (2/8) onto the
transport wheel (2/5).
6. Assembly of all opposite transport wheel ta-
kes place in the same sequence.
Assembling the upper shredder part with
cutting and motor unit (3)
1. Lift the upper shredder part onto the base and
secure it using M5x30 screws (3/1) and was-
hers 5x10x1.
Assembling the hopper (3)
1. Place the hopper onto the upper shredder part
and secure it using ST 4.2x18 screws (3/2).
STARTUP
Comply with working time regulations in force
in your country.
The extension cable must not cross over hop-
per or ejector.
The shredder can only be started when the
grass catcher is locked.
Check hopper and upper shredder part for
obstructions prior to starting the machine.
Do not use the shredder if you are:
Tired
Unwell
Under the influence of alcohol, medici-
nes and drugs
DANGER!
Danger of injury from damaged compo-
nents!
Damaged components can lead to se-
rious and even fatal injuries!
Before taking into operation, carry out a
visual inspection and check the compo-
nents for function.
WARNING!
Risk of injury due to negligence!
Negligence in handling the machine can
result in serious injuries!
Only use the shredder on firm, level
ground and in a stable setup. Do not tilt
or incline the machine during operation.
OPERATION
Operating time
The machine design supports the S6 (40 %) ope-
rating time. This means that the shredder may be
used 60 % in idle and 40 % under load. For a
time unit of 10 minutes this means 6 minutes idling
and 4 minutes under load. Continuous operation
is possible under these conditions.
Connecting the mains plug
1. Push down the cable safety (4/1) and insert
the extension cable (5/1) into the socket of the
shredder.
2. Check secure fit of the extension cable.
3. Next, connect the extension cable to your
mains voltage.
Switching on the motor
1. Press the On-switch (6/1).
Switching off the motor
1. Press the Off-switch (6/2) to switch the motor
off.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko Easy Crush MH 2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko Easy Crush MH 2800 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info