594311

Al-ko AL-KO BC 1000 E Manual

16
Zoom out
Zoom in
Previous page
1/166
Next page
16
Original instructions for use
Do not get the machine wet or expose it to moisture.
Regularly check the machine is in good working order.
Do not use any cleaning agents or solvents. They can
cause irreparable damage to the machine.
Cleaning the guard plate
1. Switch off the machine.
2. Use a screwdriver or a similar tool to remove mowing
residues carefully.
Clean the guard plate regularly in order to avoid
the stem tube overheating.
Changing the spool (Fig. 5)
1. Brace spool head (2) and use spanner (3) to loosen
fastening screw (2) clockwise.
2. Unscrew and remove fastening screw.
3. Pull the spool head off the drive shaft.
4. Remove spool (1) from the spool head.
5. Remove dirt and grass residues.
6. Thread the ends of the cutting lines from the new
spool into the openings provided for them in the spool
head.
7. Insert the spool into the spool head. Make sure that
the cutting lines do not become jammed, and pull
them out of the spool by about 9 cm.
8. Push the complete spool head onto the drive shaft
and tighten anticlockwise with the fastening screw.
9. Hold the spool head rmly and tighten with the
spanner.
Changing the line knife
1. Unscrew and remove the two screws arranged on the
inside edge of the guard plate and remove the old
line knife.
2. Insert the new line knife and screw it on again.
Do not overtighten the screws.
Sharpening the line knife
1. Remove the cutting blade from the guard plate.
2. Secure the line knife in a vice and sharpen it with a
at le.
Only le in one direction!
Trimming at fences and foundations
IMPORTANT!
Do not touch xed structures - danger of kickback!
1. Guide the machine slowly and carefully, without
allowing the cutting line to strike against obstacles.
Trimming around tree trunks
1. Carefully and slowly guide the machine around tree
trunks so that the cutting line does not touch the tree
bark.
2. Mow from left to right around tree trunks.
3. Strike the grass and weeds with the tip of the line, and
tilt the spool head forward slightly.
Trimming along stone walls, foundations and trees
results in increased line wear.
Mowing
1. Slant the spool head at a 30 degree angle to the right.
2. Turn the hand grip to the required position.
IMPORTANT!
Remove foreign bodies from the working area.
Danger of injury/damage to property due to objects
being thrown out.
Maintenance and care
CAUTION!
Danger from electrical current!
Before all maintenance and care jobs, disconnect
the machine from the mains and secure it to
prevent it from being switched back on.
After use, disconnect the mains plug and check the
machine for damage.
Keep the machine out of reach of children and
unauthorised persons.
Electrical malfunctions are only allowed to be rectied
by authorised specialist workshops.
Never use the machine if the blade of the line cutter is
missing or damaged.
Always keep the guard plate, spool head and motor
clear of mowing residues.
Do not spray the machine with water! Penetrating
water can lead to malfunctions.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko AL-KO BC 1000 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko AL-KO BC 1000 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info