594600

Al-ko AL-KO 142 Manual

31
Zoom out
Zoom in
Previous page
1/124
Next page
Preparing the equipment for use
ENGLISH 11
C) Installation of the nylon line head (available as
an accessory)
The following components should be removed when
converting the brushcutter from the 3-tooth brush
cutting blade to a nylon line head (see Fig. 5):
Retaining nut (28) (caution: left-handed thread), nut
protector (27), pressure washer (26) and metal
cutting blade.
• Fit the anti-winding protection (30) (supplied with
the line head) after the pressure piece (25). The
smooth side of the anti-winding protection faces
the gearbox, with the edge of the anti-winding
protection covering the edge of the angular
gearbox.
• Block the shaft with the pin (29).
• Screw on the line head by hand. Caution: left-
handed thread.
• Fit the protective bar (31) with assembled line
trimmer from underneath onto the guard. Bend
the protective bar slightly in the process.
Important: When using the line head, never start the
brushcutter without the protective bar and the line
trimmer assembled.
If the length of the line has been adjusted (see
chapter 8.5, "Adjusting the cutting line"), the line
trimmer will automatically cut the ends of the line to
the correct length during operation.
When using metal cutting blades, always work
without the protective bar fitted.
C) Assembly of the "Jet-Fit " cutting head
Insert the cutting line
into the main body of
the cutting head in
accordance with the
arrows on the main
body. Insert enough
line so that approx. 20
mm of the cutting line
protrudes from the
opening on the
opposite side.
Make sure that the
cutting teeth are
correctly aligned in the
direction of rotation.
Various washers are
supplied with the
cutting head.
For installation on this
type of brushcutter, use
exactly the washer
dimensions shown in
the illustration (outer
diameter, inner
diameter).
Block the shaft with the pin (29) and tighten the nut
(28). Check that the cutting head is securely seated
and properly centred.
Fit the cover of the
cutting head in place,
turn it in the direction of
the arrow and tighten it
with the combination
wrench as shown in the
illustration until it
engages.
When using the "Jet-Fit" cutting head, always use the
standard guard and the assembled protective bar.
Cutting lines must not touch the guard during rotation.
If necessary, insert the cutting lines slightly further
into the main body of the cutting head. The line
trimmer which is assembled in the protective bar is
not suitable for cutting lines. The length of the
cutting lines needs to be manually adjusted to the
correct length.
To replace a cutting
line, pull the
protruding end back
out from the main
body in the direction
of the arrow (use
universal pliers if
necessary).
Fig. 8
Fig. 9b
Fig. 9d
Fig. 9e
Fig. 9a
Fig. 9c
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko AL-KO 142 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko AL-KO 142 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info